1、货舱口围板船上安装精度检查。11 Inspection air pressure test（with water head） for No1. water ballast tank（No15 block）.No1压载水舱（No.15分段）气压试验（压头试验）检查。12 Inspection hosing test for upper deck.上甲板冲水试验检查。13 Measuring hulls main dimensions: length overall（LOA.）,length between perpendiculars（LPP.）,breath molded（B.）,depth
2、molded（D.） and deflection before launching.下水前测量船体主尺度：总长、两柱间长、型宽、型深、基线挠度。14 Inspection distance between draught marks and keel plate after marking out.划线后检查吃水标尺至平板龙骨之间的距离。15 Inspecting fitting accuracy of draught mark（loading line mark）.吃水标志（载重线标志）安装精确性检查。16 Inspection welding seam and dimension of
3、cargo hatch cover.货舱舱口盖焊缝和尺度检查。二 轮机1 Inspection machining dimension of propeller shaft（intermediate shaft or counter shaft）.螺旋桨轴（中间轴）机加工尺寸检查。2 Check for surface contact area（metallic contact） between stern shaft and propeller hub tapers. 检查螺旋桨轴与螺旋桨锥度接触面。3 Inspection machining dimension of rudder sto
4、ck.舵杆机加工尺寸检查。4 Inspection rudder carrier after assembly.上舵承组装后检查。5 Inspection machining dimension of rudder pintle.舵销机加工尺寸检查。6 Inspection alignment of stock, rudder blade and pintle.舵杆、舵叶、舵销连接后中心线检查。 Lowering test and tension test of anchor.锚投掷试验和拉力试验。 Measuring dimension of shaft coupling bolts and
5、 reamer hole.轴系连接螺栓和钻孔尺寸测量。 Inspection installation correctness of ships name plate（funnel mark）.船名牌（烟囱标志）安装正确性检查。 Flexibility and hosing test for small water tight hatch cover（water tight door and window）.水密小舱口盖（水密门、窗）启闭灵活性、冲水检查。 Tightness test（opening and closing test,emergency opening and closing
6、 test）for cargo hatch cover.货舱舱口盖密性试验（启闭试验、应急启闭试验）。 Inspecting anchor throwing away appliance.弃锚装置检查。 Inspecting centerline positioning for shaft system and rudder system before boring.轴、舵系镗孔前中心线定位检查。 Optical aligned check for shaft system after boring.轴系镗孔后光学校中检查。 Hydraulic test for L.O. pipe for s
7、tern tube.艉轴管滑油液压试验。 Measuring diameter of fore and aft stern tube bearing and bushes.艉轴管前、后轴承与衬套直径测量。17 Inspection push-up load for fore and aft stern tube bushes.艉轴管前、后衬套压入检查。18 Measuring clearance between propeller shaft & bearing.螺旋桨轴与轴承间隙测量。19 Flushing L.O.system of stern tube.艉轴管滑油系统的投油清洗。20 I
8、nspecting zero（datum） position of rudder blade.舵叶0位检查。21 Measuring clearance of rudder jumping stopper.舵止跳块的间隙测量。22 Inspecting integrity of steering gear.操舵装置完整性检查。23 Measuring installation clearance of rudder bearing.舵轴承安装间隙测量。24 Flushing of piping system for steering gear.舵机管路系统的投油清洗。25 Mooring te
9、st of steering gear.舵机系泊试验。26 Manoeuving test of steering gear during sea trial.舵机航行中操舵试验。27 Emergency manoeuving test of steering gear.舵机应急操舵试验。28 Installation and alignment inspection of windlass.锚机安装与校中检查。29 Anchoring and weighing test of windlass on sea trial.锚机航行中抛起锚试验。30 Adjusting safety devic
10、e for hydraulic system of steering gear（windlass、mooring winch）.舵机（锚机、绞缆机）液压系统安全装置调整。31 Running test and loading test for 4t provision crane.4吨食物吊运转试验和吊重试验。32 Lowering and hoisting test for life boat.救生艇收放试验。33 Loading test of accommodation ladder（pilot ladder）.舷梯（引水员梯）压重试验。34 Checking liner of main
11、 engine（M.E.）.主机垫片检查。35 Tightening inspection for through bolts of main engine（M.E.）.主机贯穿螺栓紧固度检查。36 Aligning main engines crank shaft and intermediate shaft after launching.下水后主机曲轴和中间轴连接后校中。37 Aligning intermediate shaft and propeller shaft after launching.下水后中间轴和螺旋桨连接后校中。38 Measuring deflection of
12、crank shaft of M.E. before starting up（after sea trial）.主机动车前（航行试验后）曲轴甩档测量。39 Flushing lubrication oil（fuel oil） system of M/E.主机滑油（燃油）管路投油清洗。40 Alignment inspection installation of shaft generator and gear box.轴带发电机及齿轮箱安装检查。41 Alarm testing and safety device testing of M/E.主机报警和安全装置试验。42 Mooring te
13、st（sea trial） of M.E.and inspection attached pumps and piping system.主机系泊（航行）试验并检查其附属泵与管路。43 Running test of shaft generator and clutching test between M.E. and shaft generator.轴带发电机运转试验及主机与轴带发电机之间的离合器的效用试验。44 Change over test between shaft generator and diesel generator on sea trial.航行试验中轴带发电机与柴油发电
14、机之间的换车试验。45 Overhauling main engine after sea trial.主机航行试验后的拆检。46 Installation inspection of main diesel generator.主柴油发电机组安装检查。47 Safety device testing for emergency diesel generator.应急柴油发电机的安全装置试验。48 Charging test and safety valve and automatic device adjusting for main compressor （auxiliary compre
15、ssor）.主（辅）空气压缩机的充气试验、安全阀和自动装置的调整。49 Air tightness test and safety valve adjusting for main air receiver （control air receiver, air horn receiver）on board.主空气瓶（控制空气瓶、汽笛空气瓶）装船后气密试验和安全阀的调整。50 Safety valve adjusting and accumulating test for auxiliary boiler.辅锅炉安全阀检验及蓄压试验。51 Air tightness test for auxil
16、iary boiler （economize boiler） on board.辅锅炉（废气锅炉）装船后气密试验。52 Automatic controller test for auxiliary boiler.辅锅炉自动控制装置试验。53 Function test for economizer.废气锅炉效用试验。54 Function test and automatic controller test for ballast pump.压载泵效用试验和自动控制装置试验。55 Function test of bilge oily water separator （sewage trea
17、tment plant, fresh water generator, incinerator）.舱底水油水分离器（污水处理装置、制淡装置、焚烧炉）效用试验。三 电气 Inspection main cable installation for wheel house before paneling decoration.敷板前驾驶室检查主干电缆安装. Measuring insulation resistance and reliability test protection device for main switchboard（emergency switchboard）.总配电板（应急
18、配电板）绝缘电阻测量和保护装置可靠性试验。 Load and performance test for main generator （emergency generator）.主发电机（应急发电机）负荷及特性试验。 Automatic governing test of voltage and frequency for main generator （emergency generator）.主发电机（应急发电机）电压、频率自动调节试验。 Parallel-running test for main generator.主发电机并联运行试验。 Diesel generator voltag
19、e characteristic test.柴油发电机电压特性试验。 Diesel generator governor sensitivity test.柴油发电机调速特性试验。 Test for taking on a full load suddenly.突加负荷试验。 Reverse power relay trip test.逆功率脱扣试验。 Over-current relay test.过电流脱扣试验。 Under voltage tripping test.低压脱扣试验。 Interlocking reliability test.联锁试验。 Load test for sha
20、ft generator and its function test on sea trial.轴带发电机负荷试验和航行时效用试验。 Automatic supply test of emergency generator.应急发电机自动供电试验。 Calibrating rudder angle indicator.舵角指示器校准。 Remote starting and alarm test for steering gear motor.舵机马达遥控起动和报警试验。 Function test automatic pilot.自动舵效用试验。 Sequence starting and
21、automatic exchange of motors for auxiliary machine and pump.辅机和泵的电动机程序起动和自动转换。 Charge and discharge operation test for battery and charge equipment.蓄电池和充电装置的充放电试验。 Operation test of emergency switching-off device for oil pump and ventilator （bilge pump） in engine room.机舱风、油（舱底泵）应急切断装置操作试验。 Remote co
22、ntrol test for fire pump and emergency fire pump.消防泵、应急消防泵遥控操作试验。 Function test of fog horn.雾笛效用试验。 Inspection installation and water tightness transducer of echo sounder on berth.测深仪换能器船台安装和水密性检查。 Function test and adjust error for log on sea trial.航行试验中计程仪效用试验及误差调整。 Function test and calibration s
23、elf-heterodyne curve for direction finder on sea trial.航行试验中测向仪效用试验及自差曲线校正。 Inspection installation for antenna of radio console and measuring its insulation resistance.组装报务台天线安装检查和绝缘测量。 Function test of radio console on sea trial.航行试验中组装报务台效用试验。 Calibration constant error and function for gyro-comp
24、ass on sea trial.航行试验中电罗经固定误差校正和效用试验。 Function test of radar on sea trial （mooring test）.航行试验（系泊试验）中雷达效用试验。 Simulating （Automatic） alarm test for fire detector.火警检测器模拟（自动）报警试验。 The items are tested according to mooring test program as following :下列项目按系泊试验大纲进行系泊试验： Function test of engineer calling d
25、evice（call device in hospital）.轮机员呼叫（病室呼叫）装置试验。 Function test of ultra-short wave radio telephone.超短波对讲机。 Function test of remote control system of main engine.主机遥控系统性能试验。 UMS（unattended machinery space） sea trial continue 46 hours.无人机舱作46小时航行试验。 Measuring insulation resistance for circuit.电路绝缘电阻测量。 Function test for weather facsimile receive.气象传真机效用试验。四 上层建筑 A/C duct and vent duct structure of W/H Deck.驾驶甲板空调、机械风管结构。 Inspection the structure and loading test of the lifeboat （Re
