1、H3C 交换机基本配置SwitchA# 创建手工汇聚组1。 system-viewH3C link-aggregation group 1 mode manual# 将以太网端口Ethernet1/0/1至Ethernet1/0/3加入汇聚组1。H3C interface ethernet1/0/1H3C-Ethernet1/0/1 port link-aggregation group 1H3C-Ethernet1/0/1 interface ethernet1/0/2H3C-Ethernet1/0/2 port link-aggregation group 1H3C-Ethernet1/0
2、/2 interface ethernet1/0/3H3C-Ethernet1/0/3 port link-aggregation group 1SwitchB上需要做同样的配置组网需求：在交换机上设置镜像功能，使端口e1/0/2监控端口e1/0/1的报文1.设置镜像组 SWAmirroring-group 1 local2.设置端口E1/0/2端口为监控端口、E1/0/1为源端口对进出报文都进行监控SWAmirroring-group 1 monitor-port e1/0/2SWA mirroring-group 1 mirroring -port e1/0/1 both也可以在端口视图下
3、设置：SWAinterface e1/0/1SWA-Ethernet1/0/1 mirroring -port bothSWA-Ethernet1/0/1 interface e1/0/2SWA-Ethernet1/0/2 monitor-port 3显示以太网镜像端口SWA display mirror配置VLAN：SwitchA & SwitchBSwitchAvlan 10SwitchA-vlan10port ethernet 1/0/1SwitchA-vlan10vlan 20SwitchA-vlan20port ethernet 1/0/2配置接口 SwitchAinterface
4、ethernet1/0/23SwitchA-Ethernet 1/0/23speed 100SwitchA-Ethernet 1/0/23duplex fullSwitchA-Ethernet 1/0/23port link-type trunkSwitchA-Ethernet 1/0/23port trunk permit vlan 10 to 20SwitchA-Ethernet 1/0/24speed 100SwitchA-Ethernet 1/0/24duplex fullSwitchA-Ethernet 1/0/24port link-type trunkSwitchA-Ethern
5、et 1/0/24port trunk permit vlan 10 to 20配置端口聚合SwitchAlink-aggregation group 1 mode manualSwitchA interface ethernet1/0/23SwitchA-Ethernet 1/0/23 port link-aggregation group 1SwitchA-Ethernet 1/0/23 interface ethernet1/0/24SwitchA-Ethernet 1/0/24 port link-aggregation group 1设置主机IP地址SwitchB的配置与Switch
6、A相同PC10和PC20分别处在不同的VLAN中（VLAN 10,VLAN 20）,通过设置上层三层交换机SWITCHB的从而实现两个VLAN之间的互相访问。【SwitchA交换机配置】 配置前，先将SwitchA和SwitchB 的端口24用网线进行连接。 1)配置VLAN 10,加入端口10； VLAN 20加入端口20SwitchA vlan 10SwitchA-vlan10 port Ethernet 1/0/10SwitchA vlan 20SwitchA-vlan20 port Ethernet 1/0/20 2)配置TrunkSwitchAinterface ethernet 1
7、/0/24SwitchA-Ethernet1/0/24port link-type trunkSwitchA-Ethernet1/0/24port trunk permit vlan all【SwitchB交换机配置】SwitchBvlan 10SwitchBinterface vlan-interface 10SwitchBvlan 20SwitchBinterface vlan-interface 203）在端口24配置trunkSwitchBinterface ethernet 1/0/24SwitchB-Ethernet1/0/24port link-type trunkSwitchB
8、-Ethernet1/0/24port trunk permit vlan all【主机的配置】 1）PC10: 2）PC20: .254首先，把SWTICHA的23端口和SWITCHC的23端口做好TRUNK，并允许VLAN 10 和VLAN 20 通过；把SWTICHB的24端口和SWITCHC的24端口做好TRUNK，并允许VLAN 10 和VLAN 20 通过。然后在SwitchC中做下列步骤：1、创建（进入）VLAN10 SwitchC vlan 102、创建（进入）VLAN虚接口10 SwitchCAinterface Vlan-interface 103、为VLAN 虚接口10配
9、置IP地址 4、创建（进入）VLAN20 SwitchC vlan 205、创建（进入）VLAN虚接口20 SwitchCAinterface Vlan-interface 206、为VLAN 虚接口10配置IP地址配置主机1.2.3.4.telnet远程管理交换机配置1.仅密码方式登录1配置telnet登录的IP地址 system-viewSWAinterface vlan-interface 11进入用户界面视图SWA user-interface vty 0 1设置认证方式为密码认证方式SWA-ui-vty 0authentication-mode password1设置登录验证的pas
10、sword为明文密码“999”SWA-ui-vty0set authentication password simple 9991设置登录用户的级别为最高级3（缺省为级别1）SWA-ui-vty0 user privilege level 31设置VTY0用户界面支持Telnet协议。H3C-ui-vty0 protocol inbound telnetHDLC协议的配置在接口上封装HDLC协议link-protocol hdlc打开HDLC所有报文调试信息开关 debugging hdlc all interface type number 打开HDLC事件调试信息开关 debugging
11、hdlc event interface type number 打开HDLC数据包调试信息开关 debugging hdlc packet interface type number PPP配置命令封装PPPlink-protocol ppp设置验证类型ppp authentication-mode pap|chap 设置用户名、口令、服务类型H3Clocal-user huaweiH3C-luser-huaweipassword simple sharepassH3C-luser-huaweiservice-type ppp【主验证方配置】配置验证方式 H3C-serial1/0ppp a
12、uthentication-mode pap配置用户列表 H3Clocal-user routerb H3C-luser-huaweipassword simple hello H3C-luser-huaweiservice-type ppp【被验证方配置】配置PAP用户名，密码 H3C-serial1/0ppp pap routerb password simple hello静态路由配置注意：只有下一跳所属的的接口是点对点（PPP、HDLC）的接口时，才可以填写，否则必须填写。在路由器 H3C A上配置： 路由器A的更名以及相关端口的IP地址配置H3C sysname RTARTAinte
13、rface ethernet 0/0RTA-Ethernet0/0interface serial 1/02、查看一下当前的路由表信息：RTAdisplay ip routing-table3、静态路由配置4、再次查看一下当前的路由表信息：RTAdisplay ip routing-table路由器B的配置过程类似实验结果验证： 主机之间可以相互ping通，主机和两台路由器的各个端口之间也可以相互ping通RTA:RTA ripRTA-Ethernet1/0 rip version 2 broadcastRTA-Serial0/0 link-protocol pppRTA-Serial0/0
14、rip version 2 broadcastRTA-Serial0/0 rip authentication-mode md5 usual H3CRTB:RTB ripRTB-Ethernet1/0 rip version 2 broadcastRTB-Serial0/0 link-protocol pppRTB-Serial0/0 rip version 2 broadcastRTB-Serial0/0 rip authentication-mode md5 usual H3C RTB-Serial0/1 link-protocol frRTB-Serial0/1 rip version
15、2 broadcastRTC:RTC fr switchingRTC ripRTC-Ethernet1/0 rip version 2 broadcastRTC-Serial0/0 link-protocol frRTC-Serial0/0 fr interface-type DCERTC-Serial0/0 fr dlci 20RTC-Serial0/0 rip version 2 broadcast显示RIP协议配置信息 H3C display ripRIP is runningpublic net VPN-Instance Checkzero is on Default cost : 1
16、 Summary is on Preference : 100 Validate-source-address is on Traffic-share-across-interface is off Period update timer : 30 Timeout timer : 180 Garbage-collection timer : 120 No peer router Network :第一步：打开终端显示调试信息功能terminal monitorterminal debugging第二步：打开RIP的调试开关 debugging rip packet实际显示的RIP信息 pack
17、et : vers 1,cmd Response,length 24packet : vers 1,cmd Response,length 44(1) 配置RouterARTA interface ethernet0/0RTA- ethernet 0/0 interface serial1/0/RTA ospfRTA-ospf-1 area 1RTA-ospf-1 area 0(2) 配置RouterBRTB interface ethernet0/0RTB-ethernet 0/0 interface serial1/0RTB-serial1/0 interface ethernet 1/0/0RTB ospfRTB-ospf-1 area 0RTB-ospf-1 area 2
