1、防潮箱说明书ANDBONTMDamp Proof CabinetInstruction Manual防潮箱使用手册珠海安德宝科技有限公司ZHUHAI ANDEBAO TECHNOLOGY CO.,LTD一、产品特点：1. 防潮箱采用了当今世界上最新特殊材料进行冷凝原理除湿，具有除湿快，13小时即除湿生效，且达超低湿RH25%50%。无需空箱预置运行，通电即可吸湿，控制旋钮调节，恒湿精确无故障。2. 特制除湿模块、无压缩机、无风扇、安静无噪声、无热效应、柜内RH值均匀。3. 柜体采用直流电输入，耗电小，节能环保，无漏电危险，使储存物免受高压产生漏电及火灾潜在的危险。4. 具有防潮、防蛀、防霉、防
2、锈、防变质、防尘等储存功能，是保存物品成本最低的一种储藏方式。二、适用参数相对湿度RH%理想的保存物件45%55%相机、镜头、相片、底片、CD、画、古玩、摄像机、钱币、邮票、皮革制品、光盘、半导体产品、磁带、设计图纸、乐器、显微镜35%45%精密仪器、电子电器用品、量具、精密模具、半导幻灯片、电容器、电池、光学镀膜及组件、光源、印刷线路板、精密轴承、晶体、EL、15%35%各种研究试剂、样品标本、种子、干燥花粉及香料、点心、咖啡、干燥食品、化学粉末、烟草、茶叶、草药、化学粉末、滤片15%特殊化学药品、精密电子零件、BGA、LCD三、性能说明：1. 湿度传感器精度8%RH测量范围1099%RH2
3、. 环境温度0503. 仪表响应速度快，浸水或结露后迅速恢复。4. 全互性，受温度影响小，长期稳定性和可靠性好，是目前最先进的一种控制仪。四、使用指导1. 安置平稳柜体，柜背离墙、物体510cm左右。根据要求调整放好可调节脚与层板。2. 如图1，电源隐藏的机种只要把AC插头插上即可。如图21，将整流电源插头插入可同时把储存物放置防潮柜中。3. 开机后，调节储存物最佳恒湿值（参考常用参数表达式），这时柜内机芯设备即开始工作，将柜内的湿度逐渐排出。4. 经23小时左右通过湿度表观察湿度已稳定保持在恒湿值范围。图1 机身外观部件示意图 湿度显示表 门锁 活动层板除湿机芯 AC插头图2-1 除湿心藏外
4、观（背面）供电示意图 可拆卸螺丝直流插座 电子开关电源直流转换插座 （AC100V-260V）（DC5V）五、旋钮调控说明：1. 启动调节旋钮由E旋A位，为低湿至高湿（旋转时绿色指示灯最亮为低湿，灯暗为高湿）。2. 经3小时运行，湿度指示表通常会出现比你所需湿度低，这时必须顺时钟方向把绿色灯调暗等湿度回升。3. 湿度调控旋钮的湿度标志数据为空载时的参数，由于储存物的湿度各有差异会出现与湿度指示表有偏差，所以在储物除湿时，该数据为相对湿度，此时，应以湿度指示表为准，进行旋钮调整到你所需的湿度值。4. 请根据你所存放物品参照“保存湿度参数”进行操作调湿。5. 调至你所需湿度后，如储存物没改变可不用
5、再调湿。电源指示灯 湿度调节旋钮LED显示操作说明1. 如图3，显示：用数位LED显示，显示实测相对湿度值，发光二极管（OUT）指示除湿输出状态。2. 按键：数据设置（SET）键，增加和减少键，用于设置相关参数。3. 目标湿度设置键，屏闪的数字即为目标湿度，按增减键修改。4. 按增减键，显示恒温目标，3秒钟后自动恢复恒温值。5. 关、停电有记忆，保存原来的设定值，免重新参数调整。图3 微电脑数据LED湿度控制显示器地址：广东省珠海市香洲区山星工业城110栋网站：ANDBONTMDamp Proof CabinetInstruction ManualZHUHAI ANDEBAO TECHNOLO
6、GY CO.,LTDProduct characteristics1. This product has adopted the latest cooling sets of principles in the world, clear the moisture fast, it will force between 1-2 hours. It also can achieve the lowest moisture 25%-50%RH. Without the air cabinet to work, it can absorb moisture with the electrical, t
7、he controller will adjust automatically, constant damp accurate and has no obstacles.2. Clear the moisture has patent, machine chip has no compressor, no fan, no noise, no hot effect, the RH value in cabinet is even.3. The cabinet has adopted direct electricity, has no electrical dangerous and can a
8、void the object of the goods from firing, power and energy.4. The product has no moisture, is good at preventing the moth, preventing mildew, preventing rusting, preventing bad, preventing dust in storing function. It is a way to store things which has lowest cost.Optimal Preservation ParameterRelat
9、ive Humidity RH%Optimal Preserved Article40%55%Painting, Antiques, Paper money, Stamps, Leather product, CD,LD, tape, blueprint and etc30%40%Camcorder, Camera, lens, musical instrument, Battery, 15%30%Seed, precise instrument, tobacco, herbs, chemical powder, Specimen and etc15%Seeds, articles under
10、 research, precise electronic components and etcPerformance shows1. The humidity sensors precision is small than 8% RH, the measurement ranges of 10 - 99% RH.2. Environmental temperature ranges 0 50 3. The humidity sensors speed is fast, it will rapid recovery in water or a condensation. 4. Control
11、apparatus is affected by temperature yet and the long-term stability and reliability, is the most advanced of the control apparatus.The using guideFirst, resettle the body of cabinet smoothly, put the back of cabinet off the wall about 5-10cm. According to the demand to adjust the right foot with th
12、e board.Second, as in figure 1, the hidden machine just put the AC plug in. As in figure 2-1, put this electrical plugs in also can place the object of the goods from moisture cabinet.Third, after opening the machine, adjust the storing things to be best value for a constant. (Reference the often us
13、ed of parameter expression), then the internal cabinet of the machine chip will start working, drain the humidity of the internal cabinet gradually.Fourth, after two or three hours by watching moisture, it has kept a best value for a constant.The instructions of the button1. Open to adjust the butto
14、n from E to A, is from low wet to high wet (The green sign bright is low wet， or that is high wet).2. After working 3 hours, the wet instructions watch will display lower wet that you need, than you must to adjust the green sign clockwise to wait high wet.3. The button sign data are unloaded items,
15、the storage things wet is different, so the wet instructions watch will different. The data is relative humidity when you removing the wet of storage things. Now, you should to adjust the wet you need according the wet instructions watch.4. According your storage things, reference items preserve moisture parameter to adjust wet.5. Adjust the wet that you need, if the storage things have no change, you neednt to adjust.Humidity Meter made in Germany
