1、ABB DCS 系统 培训课程 系列讲座 DownloadChapter 14 Download 14.1 General Information 14.1.1 DescriptionThis chapter describes how to download a project using Ethernet and the preparations needed.14.1.2 ObjectivesOn completion of this chapter you will be able to: Use the Serial Firmware Upgrade tool. Use the IP
2、Config tool Prepare the download of a project using the HW configuration tool. Download the project Working online and offline Describe the meaning of the different settings when downloading Download and test code. Describe the serial download (PPP).14.1.3 Reference DocumentationUse the online help:
3、 Contents tab, MaintenanceUse the online help: Contents tab, Go Online and ExecutionThe manual Control Builder Beginners Handbook 14.2 Lesson 1 Serial Firmware Upgrade14.2.1 DescriptionThis lesson describes how to use the Serial Firmware Upgrade tool.14.2.2 ObjectivesOn completion of this lesson you
4、 will be able to: Use the Serial Firmware Upgrade tool.14.2.3 The Serial Firmware Upgrade toolSelect (Start Programs ABB Control IT Control Builder Professional Serial Firmware Upgrade) from the desktop to start the Serial Firmware Upgrade tool. Use the help in the Serial Firmware Upgrade tool to re
5、ad about Firmware upgrade.14.3 Exercise 14.1 Using the Serial Firmware Upgrade toolPlease do exercise 14.114.4 Lesson 2 IPConfig14.4.1 DescriptionThis lesson describes how to use the IPConfig tool.14.4.2 ObjectivesOn completion of this lesson you will be able to: Use the IPConfig tool14.4.3 The IPCo
6、nfig toolAll controller delivered from the factory have the same IP address. You must change the IP address to an address, which is available in your own network. Use the tool IPConfig to establish contact between the engineering station and the controller and change the IP address.Do not use IPConf
7、ig for a controller when an application is running in it. IPConfig will delete every application in the controller. Ethernet addresses will be kept in the flash memory. Always close IPConfig when you are done with it, because IPConfig is using the tool port (Com4) and the rest of the CPU:s channel w
8、ill be locked.Select (Start Programs ABB Control IT Control Builder Professional IPConfig) from the desktop to start the IPConfig tool. Use the help to get information about the IPCOnfig tool.14.5 Exercise 14.2 Using the IPConfig toolPlease do exercise 14.214.6 Lesson 3 Download using Ethernet14.6.1
9、 DescriptionThis lesson describes how to download using Ethernet.14.6.2 ObjectivesOn completion of this lesson you will be able to: Prepare the download of a project using the HW configuration tool. Download the project Working online and offline Describe the meaning of the different settings when d
10、ownloading14.6.3 The HW configuration tool14.6.4 Preparation of download in HW ConfigurationMake sure you configure the hardware structure correct before you make a download.14.6.4.1 Ethernet address setting in CPUSet correct IP addresses on the Ethernet channels. Make sure it is the same addresses
11、as you used when you made the IPConfig. Right-click on the 1 Ethernet icon and select Editor. Change the IP address from 172.16.0.0 to correct address, dont forget to change the IP subnet mask. Same procedure for the second Ethernet channel.14.6.4.2 Set System IdentityThe system identity is the same
12、 IP address as on CN1 on the AC800M.14.6.5 Download Project and Go OnlineSelect (Tools Download Project and Go Online) from the menu of the Project Explorer to download the project.14.6.5.1 ApplicationsWhen you go to Online via the (ToolsDownload Project and Go Online) a version analysis of the appl
13、ications is made. The analysis results are used to determine if and how applications shall be updated to new versions in the controllers. If you have made changes to one or several applications in Offline mode the version analysis detects it. You can then, when selecting (ToolsDownload Project and G
14、o Online), decide how to restart the changed applications. Independent of how you restart the applications, the changed application parts are downloaded to the controllers. The controller will stop the applications and restart with the new and changed application. 14.6.5.2 RestartThe influence of Wa
15、rm restart and Cold restart on Non Retain, Retain and Cold Retain Variables.14.6.5.2.1 Warm Restart At a Warm Restart, variables with the attribute retain or coldretain are stored before restart. Variables without these attributes are given their base value or initial value.14.6.5.2.2 Cold RestartAt
16、 a Cold Restart, variables without the attribute coldretain lose their values. Instead, they are given their initial value or base value. Variables specified using the attribute coldretain keep their values. Cold restart is disabled if the application is changed and Apply Changes is set to No in the
17、 Online with download dialog box.14.6.5.2.3 Cold Restart AllThe Cold restart All command affects all applications displayed in the list, not only the selected application. By pressing the button, the start mode is set to cold for all applications.14.6.5.3 Apply ChangesThe command Apply Changes shows
18、 the current settings for the selected application. There are two buttons - Yes and No. If it is possible to change the setting, the buttons are enabled, otherwise disabled. If the user changes this setting, it immediately affects the setting in the list and the Remarks column is updated if needed.
19、The Apply Changes section and buttons are not visible if the user has chosen Simulate or Online without Download. For each changed application in the project the user can decide to apply the changes in the application or not to apply them. For some changes, for example for tasks and I/O connections,
20、 there is a dependency between the application and the controller configuration. For such cases a choice in one of the sections (Applications or Controller Configurations) may set the choice in the other section automatically. This dependency cannot be overridden.14.6.5.4 InformationThe Application
21、Analysis Information dialog box display information about the application. It is divided into four sections. General Programming tool Actions Online statusFor more information use the online help. Select the Contents tab, Go Online and Execution Go Online.14.6.6 Controller Configurations14.6.6.1 App
22、ly Changes The command Apply Changes shows the current settings for the selected application. There are two buttons - Yes and No. If it is possible to change the setting, the buttons are enabled, otherwise disabled. If the user changes this setting, it immediately affects the setting in the list and
23、 the Remarks column is updated if needed. The Apply Changes section and buttons are not visible if the user has chosen Simulate or Online without Download. For each changed application in the project the user can decide to apply the changes in the application or not to apply them. For some changes,
24、for example for tasks and I/O connections, there is a dependency between the application and the controller configuration. For such cases a choice in one of the sections (Applications or Controller Configurations) may set the choice in the other section automatically. This dependency cannot be overr
25、idden.14.6.6.2 InformationThe Controller Analysis Information dialog box displays information about the controllers. It is divided into two sections. Remarks ApplicationsFor more information use the online help. Select the Contents tab, Go Online and Execution Go Online.14.7 OnlineIt is possible to
26、go online if you have the same project in you computer as the one in the Controller(s). Select (Tools Online) from the menu in the Project Explorer. It is not possible to go Online if you have made changes the project, you must then make a new download. 14.8 OfflineSelect (Tools Offline) from the me
27、nu in the Project Explorer if you want to go offline.14.9 Exercise 14.3 DownloadingPlease do exercise 14.314.10 Lesson 4 Serial download (PPP)14.10.1 DescriptionThis lesson describes the theory how to do a serial download by using Point-to-Point Protocol (PPP).14.10.2 ObjectivesOn completion of this
28、 lesson you will be able to: Describe the serial download (PPP).14.10.3 Download the Project via RS 232PPP must be installed on your computer when you intend to download a project via RS 232. Read chapter 6.5 in the (Online) manual Control Builder Beginners HandBook, to get information about downloa
29、ding via RS 232. Du kan tag bort denna osynliga text men ltnedanstende Page Break ligga kvar !Lt ven den efterfljande sidan ligga kvar !This page is intentionally left blankThis page is intentionally left blankOsynlig text:Nsta sida mste brja p UDDA sidnummerLmna EN eller TV tomma sidor hr OVANFR.Ne
30、danstende Section Break fr INTE tas bort !Komplettera tom sida vid behov med nedanstende textThis page is intentionally left blank TABLE OF CONTENTSChapter 14 Download 114.1 General Information 114.1.1 Description 114.1.2 Objectives 114.1.3 Reference Documentation 114.2 Lesson 1 Serial Firmware Upgr
31、ade 214.2.1 Description 214.2.2 Objectives 214.2.3 The Serial Firmware Upgrade tool 214.3 Exercise 14.1 Using the Serial Firmware Upgrade tool 214.4 Lesson 2 IPConfig 314.4.1 Description 314.4.2 Objectives 314.4.3 The IPConfig tool 314.5 Exercise 14.2 Using the IPConfig tool 314.6 Lesson 3 Download using Ethernet 414.6.1 Description 414.6.2 Objectives 414.6.3 The HW configuration tool 414.6.4 Preparation of download in HW Configuration 414.6.4.1 Ethernet address setting in CPU 414.6.4.2 Set System Identity 414.6.5 Download Project and Go Online 414.6.5.1 Applications 514.6.5.2 Restart 514.
