CGMP文件分析天平的操作校验和维护程序SOP文档格式.docx
- 文档编号:19072449
- 上传时间:2023-01-03
- 格式:DOCX
- 页数:18
- 大小:28.17KB
CGMP文件分析天平的操作校验和维护程序SOP文档格式.docx
《CGMP文件分析天平的操作校验和维护程序SOP文档格式.docx》由会员分享,可在线阅读,更多相关《CGMP文件分析天平的操作校验和维护程序SOP文档格式.docx(18页珍藏版)》请在冰豆网上搜索。
Make
仪器编号
IDNO
型号
Model
序列号
Srno
量程
Capacity
最大称样量
MaximumWt
最小称样量
MinimumWt
210g±
0.1mg41g±
0.01mg
200g
10mg
位置:
检测中心天平室
Location:
QualityControlDepartment(BalanceRoom)
3.0定义Definitions:
无Nil
4.0责任Responsibility:
分析天平的操作与校验由检验员负责。
TheresponsibilityofoperationandtoverifytheperformancecheckofAnalyticalbalanceslieswithQC.Analyst.
5.0程序Procedure:
5.1操作Operation:
5.1.1观察水平仪的气泡是否处于中心确认天平是否处于水平。
如果没有,通过调节天平后方的地脚螺钉直至气泡处于中心位置。
Ensurethatthebalanceisleveledbyobservingtheairbubbleisinthecenteroflevelindicator.Ifnotadjustthelevelingbyturningfootscrewsattherearsideofthebalancehousinguntilthebubbleisinthecenterofthelevelindictor.
5.1.2打开天平电源开关。
Switch‘ON’themainswitchofthebalance.
5.1.3按“ON/OFF”键。
Press“ON/OFF”key.
5.1.4等30秒天平初始化后,天平显示‘0.00000’g。
否则按‘→0←’键。
Waitforabout30secondsfortheinitializationofthebalance.Afterinitializationthebalancedisplays‘0.00000’g.Otherwise,press‘→0←’key
5.1.5当天平显示’0.00000’时,可以对天平开始操作。
When’0.00000’isdisplayed,thebalanceisreadyforoperation.
5.1.6将称量纸或称量瓶置于称量盘中心,关上天平玻璃门。
Placetheemptycontainer/butterpaperonthecenterofthepanandclosetheslidingglassdoors.
5.1.7等读数稳定。
Waittillthebalanceshowsstablereading.
5.1.8按‘→T←’键清零,显示变为‘0.00000’g。
称量纸或称量瓶的重量被去皮重了。
Taretheweightbypressing‘→T←’keybriefly.Thedisplaychangesto‘0.00000’g.Nowtheweightofthecontainer/paperistared.
5.1.9加入称量样品达到规定量。
Addweighingsampletothecontainer/papertilltherequiredweightisdisplayed.
5.1.10等读数稳定。
记录数据为总重量g。
Waituntilthebalanceshowsstablereading.Recordtheweightas“GrossWting”.
5.1.11小心将样品移入量瓶后,将称量纸或称量瓶小心放置在称量盘中。
Transferthesamplecarefullyintotheflaskandplacethebutterpaperorweighingobjectonthepancarefully.
5.1.12关上天平玻璃门等读数稳定,记录数据为皮重g。
Closethedoorsandwaittillthebalanceshowsstablereading.Recordtheweightas“TareWting”.
5.1.13称量mg样品,按天平右边的‘F’键。
显示变为‘‘0.00’mg,接着按照5.1.6步骤进行称量。
Toweighthesamplein‘mg’,press‘F’keyintherightsideofthebalance.Thedisplayconvertsinto‘0.00’mgandcontinuefromstep5.1.6fortoweigh.
5.2提示Precautions:
5.2.1天平必须避免振动、风吹、高温、高湿。
Thebalanceshouldbefreefromvibration,airthrust,strongheatandmoisture.
5.2.2AG245天平称量范围不得超过200g。
Donotweighbeyondtheweighing200gonAG245balancefortheanalyticalwork.
5.2.3读数稳定后再确认数据。
Considerweightreadingsoftheobservationstillconstantreadingisdisplayed.
5.2.4称量之前确保称量盘是干净的。
用软毛刷清洁称量盘。
Ensurethepaniscleanedbeforeweighing.Cleanthepanwithsoftbrush.
5.3校验Performancecheck
5.3.1分析天平的日校验DailyPerformancecheckAnalyticalBalance
5.3.1.1去除称量盘负载,清洁称量盘及其周围。
Removeanyloadfromtheweighingpan,cleanthepanandarea.
5.3.1.2持续按右上角的“Cal”键至显示“CalibrationInternal”。
Press“Cal”keyattherighttopforawhiletoperform“CalibrationInternal”.
5.3.1.3天平显示自校:
开始显示+200.00000g结束显示0.00000g。
Balanceshowscalibrationinternal,then+200.00000gandfinally0.00000g.
5.3.1.4将10mg标准砝码置于称量盘中央,记录读数。
Place10mgstandardweightatthecenterofthepanandrecordthedisplayreading.
5.3.1.5将100mg标准砝码置于称量盘中央,等显示稳定记录读数。
Place100mgstandardweightatthecenterofthepanandrecordthedisplayreadingtillconstantreadingisdisplayed.
5.3.1.6将200g砝码置于称量盘中央,将读数记录在天平校验记录里。
Placetheweight200gatthecenterofthepanandrecordtheobservedreadinginPerformancecheckRecordofAnalyticalBalance.
5.3.1.7将校验细节记录在如附录I所示分析天平校验记录里。
RecordthePerformancecheckdetailsinthePerformancecheckRecordofAnalyticalBalanceasshowninAnnexure-I.
5.3.2月校验(多个标准砝码)
Monthlyperformancecheck(withmultiplestandardweights)
准确度Accuracy:
5.3.2.1用标准砝码校验天平。
Checktheperformancecheckofthebalancebyusingstandard
weights.
5.3.2.2将200mg,500mg,1g,2g,5g,10g,20g,50g,100g,200g标准砝码置于称量盘中央,记录读数。
并奖结果记录在附录II所示的表格里。
Place200mg,500mg,1g,2g,5g,10g,20g,50g,100g,200g,standardweightsatthecenterofthepanandrecordtheobservedreadings.TabulatetheresultsinMonthlyPerformancecheckrecordofAnalyticalbalanceasshowninAnnexure-II.
5.3.3标准限度AcceptanceCriteria:
标准砝码重量StandardWeight
限度范围AcceptanceRange
USP等级ClassasperUSP
+0.05mg
1
100mg
+0.10mg
200mg
+0.12mg
4
500mg
1g
+0.20mg
2g
5g
+0.30mg
10g
+0.50mg
20g
+0.70mg
50g
+1.20mg
100g
+2.0mg
+4.0mg
5.3.4重复性实验MeasurementofRepeatability:
5.3.4.1确保标准砝码使用前已校验合格。
Ensurethatthestandardweightsarecalibratedpriortotheiruse.
5.3.4.2确保天平做重复性实验前已校验合格。
Ensurethatthebalanceischeckedforperformancecheckpriortotherepeatabilitystudy.
5.3.4.3将100mg标准砝码置于分析天平称量盘中央。
Takethe100mgstandardweightandplaceitatthecenterofthepanoftheanalyticalbalance.
5.3.4.4记录读数。
用同一标准砝码重复称10次,计算标准偏差值。
Recordthereadingonthedisplay.Repeatthestepfortentimeswiththesamestandardweightandcalculatethestandarddeviationofthedisplayweights.
5.3.4.5用1g和100g标准砝码重复5.3.4.3和5.3.4.4的步骤,计算标准偏差值。
Repeat5.3.4.3and5.3.4.4with1gand100gofthestandardweights,calculatethestandarddeviationoftheweights.
5.3.4.6将重复性数据记录在附录III所示的表格里。
RecordtheRepeatabilitydatainthePerformancecheckrecordasshowninAnnexure-III.
5.3.4.7如果重复性实验中出现任何偏差,必须对偏差进行调查,而且必须进行内部或代理商的校正。
IncaseofanydeviationfoundduringRepeatability,deviationshouldbeinvestigatedandshouldbecorrectedbyin-houseorbyexternalagency.
5.3.4.8校正后,天平必须进行机能检查和重复性实验。
Aftercorrecting,thebalanceshouldbetestedforPerformancecheckandtestedforrepeatability.
5.3.5置信度Uncertainty,precision(repeatability):
5.3.5.1用100mg、1gand100gm的重复性数据计算不可信度
Calculatetheuncertaintyvaluefor100mg、1gand100gmstandardweightsundermeasurementofrepeatability.
3x标准偏差
计算公式:
-------------------------------------------
标准砝码重
3xStandardDeviation
Calculation:
StandardWeight
5.3.5.2限度范围:
≤0.001
AcceptanceCriteria:
Shouldnotbemorethan0.001.
5.4校验周期FrequencyforCalibration:
5.4.1用指定标准砝码进行每日校验。
Dailyperformancechecktobedonebyusingspecifiedstandardweights.
5.4.2多标准砝码校验周期:
一个月+2天。
Performancecheckwithmultiplestandardweightsshallbecarriedoutonceinamonth+2days.
5.4.3重复性实验周期:
Repeatabilityshallbedoneonceinamonth+2days.
5.5维护计划MaintenanceProgram:
5.5.1当天平观察到需要维修/未通过校验时,应贴上“维修”标签(附件V),同时向QC经理报告。
Put“UNDERMAINTENANCE”label(Annexure-V)ontheinstrumentwhenitwasobservedbreakdown/oroutofcalibration,intimatetoQ.C.Manager.
5.5.2QC经理通知仪器售后服务工程师,经修理后需校验仪器,检查是否正常工作并记录。
(注意:
本次校验为额外校验,应按照校验日程计划照常进行每月的校验)。
Q.C.ManagerinformstotheInstrumentserviceengineer.Aftermaintenance,calibratetheinstrumenttocheckitssatisfactoryfunctioningandrecordthereadings.(Note:
Calibratetheinstrumentasperthemonthlycalibrationschedule,thiscalibrationisanadditional)
5.5.3将仪器维修报告附在仪器维护历史文件中,按照附件VI的格式填写仪器故障的详细情况。
RetainservicereportcopyattachedintheInstrumentMaintenanceHistoryFileandenterthebreakdowndetailsintheenclosedformatasAnnexure-VI.
6.0相关文件RelatedDocuments:
6.1分析天平日校验记录(附录-I)
Dailycalibrationrecordofanalyticalbalance(Annexure-I)
6.2分析天平月校验记录(附录-II)
MonthlycalibrationofrecordofAnalyticalBalance(Annexure-II)
6.3分析天平重复性实验记录(附录-III)
Precision(repeatability)ofanalyticalbalance(Annexure-III)
6.4校验状态标签(附录-IV)
Calibrationstatuslabel(Annexure-IV)
6.5“维修”标签(附录-V)
“UNDERMAINTENANCE”label(Annexure-V)
6.6仪器维修记录(附录-VI)
MaintenanceRecord(Annexure-VI)
6.7仪器使用记录(附录-VII)
INSTRUMENTUSAGELOGBOOK(Annexure-VII)
7.0修订记录RevisionRecord:
序号
Sl.No
版本号
RevisionStatus
修订内容
DetailsofRevision
备注
Remarks
******文件终结符ENDOFDOCUMENT
附录I
ANNEXURE-I
分析天平每日校验记录
DAILYPERFORMANCECHECKRECORDOFANALYTICALBALANCE
参照文件编码Doc.Ref.No.:
表格号FormNo.:
生效日期EffectiveDate:
第1页共1页Page1of1
仪器编号ID.No.序列号S/N:
生产厂家型号Model:
MAX:
200gMIN:
10mg
日期Date
水平
Spirit
Level
内校
InternalCalibration
砝码重量
StandardWeight
读数
DisplayReading
误差
Difference
限度范围
Acceptance
criteria
校验人
Calibratedby
复核人
Checkedby
10.00mg
0.05mg
100.00mg
0.10mg
200.0000g
4.0mg
附录II
ANNEXURE-II
分析天平每月校验记录
MONTHLYPERFORMANCECHECKRECORDOFANALYTICALBALANCE
参照文件编码Doc.Ref.No.:
表格号FormNo.:
生效日期EffectiveDate:
仪器编号序列号S/N:
生产厂家Make:
型号Model:
10mg准确度Accuracy
日期
Date
SpiritLevel
内校InternalCalibration
标准砝码重量
Standardweight
DisplayReading
AcceptanceCriteria
200.00mg
0.12mg
500.00mg
1.00000g
0.20mg
2.00000g
5.00000g
0.30mg
10.00000g
0.50mg
20.00000g
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- CGMP 文件 分析 天平 操作 校验 维护 程序 SOP