进口压力容器产品安全性能监督检验实施细则正式Word格式文档下载.docx
- 文档编号:19749296
- 上传时间:2023-01-09
- 格式:DOCX
- 页数:6
- 大小:81.24KB
进口压力容器产品安全性能监督检验实施细则正式Word格式文档下载.docx
《进口压力容器产品安全性能监督检验实施细则正式Word格式文档下载.docx》由会员分享,可在线阅读,更多相关《进口压力容器产品安全性能监督检验实施细则正式Word格式文档下载.docx(6页珍藏版)》请在冰豆网上搜索。
Chapter1GeneralProvisions
1、为保证进口压力容器产品制造质量监督检验质量,制订本细则。
1Thisoutlineisformulatedinordertoensureeffectivesupervisoryinspectionofthepressurevesselproductsimported
2、与进口压力容器产品制造质量监督检验有关各方及人员,均应遵守本细则。
2Thisoutlineisapplicabletowhomrelevanttothesupervisoryinspectionforsafetyperformanceofthepressurevesselproductsimported
二、依据
Chapter2SupervisoryInspectionBasis
1、中华人民共和国国务院令第373号《特种设备安全监察条例》;
1SpecialEquipmentSafetySupervisionRegulation(PromulgatedbyDecreeNo.373oftheStateCouncilofthePeople'
sRepublicofChina)
2、中华人民共和国国家质量监督检验检疫总局令第22号《锅炉压力容器制造监督管理办法》;
2SupervisionAdministrationRegulationforManufactureLicensingofBoilerandPressureVessel.(PromulgatedbyDecreeNo.22ofGeneralAdministrationofQualitySupervision,InspectionandQuarantineofthePeople'
3、《压力容器安全技术监察规程》;
3SupervisionRegulationontheSafetyTechnologyforPressureVessel.(PromulgatedbySafetySupervisionDepartmentofGeneralAdministrationofQualitySupervision,InspectionandQuarantineofthePeople'
4、《锅炉压力容器产品安全性能监督检验规则》。
4SupervisoryInspectionRuleforSafetyPerformanceofBoilerandPressureVesselProducts.(PromulgatedbySafetySupervisionDepartmentofGeneralAdministrationofQualitySupervision,InspectionandQuarantineofthePeople'
三、监督检验内容
Chapter3ContentsofSupervisoryInspection
1、对压力容器制造过程中涉及安全性能的项目进行监督检验;
1.Supervisoryinspectingtheitemsrelatedtothesafetyperformanceoftheproductduringpressurevesselmanufacturing.
2、对受检企业压力容器制造质量体系运转情况进行监督检查。
2.Supervisoryexaminingtheimplementationofthequalitysystemofthesupervisedmanufacturer.
四、监检项目和方法
Chapter4ItemsandMethodsofSupervisoryInspection
1、图样资料
1.Drawinganddata
(1)检查压力容器设计单位的设计资格印章,确认资格有效。
(1)Examinethecertificateofpressurevesseldesigner,confirmtheeffectivenessofitsqualification.
(2)审查压力容器制造和检验标准的有效性。
(2)Reviewtheeffectivenessofstandardsonmanufactureandinspectionforpressurevessel.
(3)审查设计变更(含材料代用)手续。
(3)Reviewtheapprovalformalitiesfordesignchange(includingmaterialsubstitution).
2、材料
2.Materials
(1)审查材料质量证明书、材料复检报告。
(1)Checkmaterialcertificateandmaterialre-testreport.
(2)检查材料标记移植。
(2)Checkthetransplantationofmaterialidentification.
(3)审查主要受压元件材料的选用和材料代用手续。
(3)Checktheselectionandformalitiesofsubstitutematerialsformainpressureparts.
(4)根据ASME某些材料的特殊要求,确认焊接、热处理、加工工艺及检验工艺的正确性。
(4)Confirmtheconformityofweldingprocedure,heat-treatment,processingprocedureandinspectionprocedurewiththespecialrequirementsofaccordingsomematerialtoASMEcode.
3、焊接
3.Welding
(1)审查焊接工艺评定及记录,确认产品施焊所采用的焊接工艺符合相关标准、规范。
(1)Checktheweldingprocedurequalificationandtheirrecords,verifythattheweldingtechnologyusedinproductproductionisinaccordancewiththerelevantstandardsandcodes.
(2)确认焊接试板数量及制作方法。
(2)Confirmthenumberandmanufacturingmethodoftheweldingtestplate.
(3)审查产品焊接试板性能报告,确认试验结果。
(3)Checkthepropertytestreportoftheproductweldingtestplatesandconfirmthetestresults.
(4)检查焊工钢印。
(4)Checkidentificationsteelstampsofweldersandweldingoperators.
(5)审查焊缝返修的审批手续和返修工艺。
(5)Checkformalitiesandproceduresforweldingrepair.
4、外观和几何尺寸
4.Visualanddimensionalexamination
(1)检查焊接接头表面质量。
(1)Examinetheappearanceofweldedjoints.
(2)检查母材表面的机械损伤情况。
(2)Checkthemechanicaldamageonthesurfaceofbasemetal.
(3)检查筒体内径与最小内径差,当直立容器壳体长度超过30m时,检查筒体直线度。
检查焊缝布置和封头形状偏差,并记录实际尺寸。
(3)Checkthedifferencebetweenmaximumandminimumdiametersofshell.Checkthestraightnessofthecylinderofverticalvesselwithheightmorethan30meters,Checkthearrangementofweldsandthedeviationoffigureinheadandrecordtheiractualdimensions.
5、无损检测
5.Non-destructiveexamination
(1)检查布片(排版)图和探伤报告,核实探伤比例和位置,对局部探伤产品的返修焊缝,应检查扩探情况。
对超声波探伤和表面探伤,除审查报告外,监检人员还应不定期到现场对产品进行实地监检。
(1)Checkx-rayfilmarrangementmapandNDEreport.VerifytheproportionandpositionofNDE.Forthespot-NDEpressurevessel,checktheextensionRTfortherepairedwelds.AsfortheUTorsurfaceflawdetection,thesupervisoryinspectorshouldconductrandomon-sitesupervisoryinspectioninadditioncheckingthereport.
(2)抽查底片。
抽查数量不少于设备探伤比例的30%,且不少于10张(少于10张的全部检查),检查部位应包括T形焊缝可疑部位及返修片。
(2)Checkthex-rayfilms.Thenumberofthex-rayfilmsbeingcheckedshouldnotbelessthan30percentofthewholeandshouldnotlessthan10films(includingthex-rayfilmsatT-joint,doubtfulareaandattherepairedarea).
6、热处理
6.Heattreatment
检查确认热处理记录曲线和热处理工艺的一致性。
Checkandconfirmthecorrespondencebetweenheattreatmentcurveandactualheattreatmentparameterandprocedure. 7、耐压试验
7.Pressuretest
耐压试验前,应确认需监检的项目均监检合格,受压企业应完成的各项工作均有见证。
耐压试验时,监检人员必须亲临现场,检查试验装置、仪表及准备工作,确认试验结果。
Beforepressuretest,confirmthatallrequireditemshavepassedthesupervisoryinspectionandthesupervisedmanufacturerhaskeptthetestimonyofthewhole-completedwork.Duringpressuretest,thesupervisoryinspectorshallcheckthetestequipment,instruments,preparationworkfortestingandverifythetestresultsonthesite.
8、安全附件
8.Safetyappurtenance
检查安全附件数量、规格、型号及产品合格证应当符合要求。
Thenumber,specifications,typesandcertificatesofcomplianceofsafetyappurtenancesshouldmeettherequirements.
9、气密性试验
9.Leaktest
检查气密性的试验结果,应当符合有关规范、标准及设计图样的要求。
Checktheleaktestresulttoassurethatitmeetstotherequirementsofconcernedcode,standards,anddesigndrawing.
10、出厂技术资料
10.Deliverytechnicaldata
(1)审查出厂技术资料。
Checkthetechnicaldatatobedelivered.
(2)检查铭牌内容应符合有关规定,在铭牌上打监检钢印。
Checkthenameplateifthecontentsonitareinaccordancewiththerelevantrequirements,ifso,stampthesupervisoryinspectionsteelsealontheproduct'
snameplate.
11、监检资料
11.Supervisoryinspectiondata
经监检合格的产品,监检人员应当根据《压力容器产品安全性能监督检验项目表》的要求及时汇总、审核见证资料,并由监检单位出具《监检证书》。
Oncetheproducthaspassedthesupervisoryinspection,thesupervisoryinspectorshouldsummarizeandverifythetestifyingpaperintimeaccordingtotheSupervisoryInspectionItemsforSafetyPerformanceofPressureVesselProductsandissuetheSupervisoryInspectionCertificate.
五、监检程序
Chapter5SupervisoryInspectionProcedure
1、受检企业资质、质量体系、人员资格及生产能力确认,内容包括:
1.
Thecertificate,qualitymanagementsystem,personnelqualificationandproductioncapabilityofthesupervisedmanufacturershouldbeconfirmed,whichinclude:
(1)、审查受检企业制造许可证,确认其有效性;
(1)
Examinethecertificateofpressurevesselmanufacturer;
confirmtheeffectivenessofitsqualification.
(2)、审查受检企业的质量体系文件(包括质量手册、程序文件、管理制度、各责任人员的任免文件、质量信息反馈资料等)是否符合要求;
(2)
ReviewtheDocumentsonqualitysystem(includingqualitymanual,procedures,managementrules,documentsonappointmentanddismissofresponsiblepersons,andqualityinformationfeedbackdata),ConfirmthattheDocumentsonqualitysystemmeettherequirementsofcorrespondingcodes.
(3)、审查从事锅炉压力容器焊接的持证焊工的持证项目、有效期等是否符合要求;
(3)
Checkthequalifieditems,termsofvalidityofthequalifiedwelders.Thequalifieditems,termsofvalidityofthequalifiedweldersengagedintheweldingofpressurevesselproductsshouldmeettherequirementsofcorrespondingcodes.
(4)、审查从事锅炉压力容器质量检验的人员及从事无损检测人员的持证项目、级别、有效期等是否符合要求;
(4)
Checkthequalifieditems,qualifiedlevelandtermsofvalidityofthelistofstaffengagedinnon-destructiveexaminationandqualityinspection.Theirqualifieditems,qualifiedlevelandtermsofvalidityshouldmeettherequirementsofcorrespondingcodes.
(5)、审查压力容器的设计资料,工艺文件,制造、检验控制程序,以及焊接工艺评定一览表等;
(5)
Reviewthepressurevesseldesigndata,manufactureproceduredocuments,manufactureandinspectioncontrolprocedure,aswellasthelistofweldingprocedurequalifications.
(6)、查看并确认受检企业的生产能力。
(6)
Checkandverifytheproductioncapabilityofthesupervisedmanufacturer.
2、按《监检项目表》(见附件)的内容实施监检工作。
2.
SupervisoryinspectionshouldbeimplementedaccordingtothecontentsofSupervisoryInspectionItems(Appendix1).
(1)、压力容器产品监检项目分A类和B类。
对A类项目,监检员必须到场进行监检,并在受检企业提供的相应的见证文件(检验报告、记录表、卡等,下同)上签字确认;
未经监检确认,不得流转至下一道工序。
对B类项目,监检员应到场进行监检,如不能到场监检,可在受检企业自检后,对受检企业提供的相应见证文件进行审查并签字确认。
TheSupervisoryInspectionItemsofpressurevesselproductsareclassifiedintoCategoryAandCategoryB.
FortheitemsofCategoryA,thesupervisoryinspectormustconductsupervisoryinspectiononthesiteandshouldsignontherelatedtestifyingdocumentsprovidedbythesupervisedmanufacturer(includinginspectionreport,recordingformsandcards;
similarlyhereinafter).Iftheitemhasnotbeenverifiedviasupervisoryinspection,theproductcannotbetransferredtothenextworkingprocess.
FortheitemsofCategoryB,Thesupervisoryinspectormustconductsupervisoryinspectiononthesite.Ifthesupervisorinspectionisnotonthesite,he(orshe)shouldcheckandsignontherelatedtestifyingdocumentsprovidedbythesupervisedmanufacturertovalidatetheself-inspectionofthemanufacturer.
(2)、受检单位企业发生质量体系运转和产品安全性能违反有关规定的一般问题时,监检员应当向受检企业发出《锅炉压力容器产品安全性能监督检验工作联络单》;
发生违反有关规定的严重问题时,监检单位应当向受检企业签发《锅炉压力容器安全性能监督检验意见通知书》,并报告国家质检总局安全监察机构。
Whenthesupervisedmanufacturermakessuchgeneralm
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 进口 压力容器 产品 安全 性能 监督 检验 实施细则 正式