B3QA068ICSIP进料检验规范Word格式.docx
- 文档编号:19761679
- 上传时间:2023-01-09
- 格式:DOCX
- 页数:13
- 大小:152.79KB
B3QA068ICSIP进料检验规范Word格式.docx
《B3QA068ICSIP进料检验规范Word格式.docx》由会员分享,可在线阅读,更多相关《B3QA068ICSIP进料检验规范Word格式.docx(13页珍藏版)》请在冰豆网上搜索。
資材處;
稽核室;
中國辦事處
ReviewBoard
核准
ApprovedBy
審核
ReviewedBy
製訂
PreparedBy
發
行
Issue
AllenHuang
n/a
MarkJiang
1.目的:
Purpose
本作業標準書之制定目的為IC品質檢驗之依據,以確保生產之品質而制定。
IssueICstandardinspectproceduretomakesurethequality.
2.適用範圍:
Scope
本規範為鋇鎝設計之產品為檢驗判定基準,但我方客戶若有不同的要求規格者,應以客戶規格優先採用如客戶無特別要求,仍沿用本檢驗規範。
ThisstandarddefinesthecommoncosmeticinspectioncriteriaforBitaTEKproductsexceptthefollowingsituations:
2.1.如果客戶依本身所需求而提供檢驗規範.本公司依客戶提供檢驗規範為品質檢驗之依據。
Customer’sstandardwillbefollowedifcustomerprovidesit.
2.2.如果客戶無特別要求,則依本檢驗規範為品質檢驗之依據。
Ifpartsdrawingorapprovalsheetspecifytherequirement,theinspectionwillfollowit.
2.3.如果客戶有提供樣品,則依客戶提供之樣品或設計者在圖面或承認書有特殊規定為品質檢驗之依據。
Ifdesignerprovidesapprovedgoldensamples,theinspectionwillfollowit.
3.名詞定義AppearanceDefinition:
3.1真空防潮包装
(Drypack)
防潮包裝是一種抗潮濕的IC包裝方式,IC經過烘乾後立即放入真空袋內。
DrypackingrequirementsforthevariousmoisturesensitivitylevelsareshowninTITEM6.4.
3.2防潮袋MoistureBarrierBag(MBB)
用於設計包裝溼敏元件的包裝袋,以防止水氣。
Abagdesignedtorestrictthetransmissionofwatervaporandusedtopackmoisturesensitivedevices.
3.3.溼度指示卡HumidityIndicatorCard(HIC)
溼度指示卡主要用以藍色及粉紅色顯示該防潮袋內溼度受潮比率,其必須與防潮袋一起包裝於內。
Acardonwhichamoisture-sensitivechemicalisappliedsuchthatitwillmakeasignificant,perceptiblechangeincolor(hue),typicallyfromblue(dry)topink(wet)whentheindicatedrelativehumidityisexceeded.TheHICispackedinsidethemoisture-barrierbag,alongwithadesiccant,toaidindeterminingthelevelofmoisturetowhichthemoisture-sensitivedeviceshavebeensubjected.
3.4.防潮警告標籤MoistureSensitiveIdentificationLabels
防潮警告標籤必須貼於防潮袋外,該標籤必須印有警告標示(如下圖),並於標籤必標名IC耐熱溫度(Peakpackagebodytemperature),保存期限(floorlife)包裝日期(bagsealdate)。
Labels-MoistureSensitiveIdentificationLabelsrelevanttothedrypackprocessarethe“Moisture-SensitiveIdentification”(MSID)labelandtheCautionlabelasspecifiedinJEDECJEP113(seeasbelowphoto).TheMSIDlabelshallbeaffixedtothelowest-levelshippingcontainerthatcontainstheMBB.TheCautionlabelshallbeaffixedtotheoutsidesurfaceoftheMBB.TheCautionlabelincludesfieldsforthePeakpackagebodytemperatureallowedduringreflowsoldering(theclassificationtemperatureperJ-STD-020),thefloorlife,andthebagsealdate.
4.檢驗條件InspectCondition:
檢驗條件規格如下:
Inspectionconditionasfollowing
4.1.燈光亮度:
檢查環境的四周燈光亮度須要在500LUX以上.燈光顏色白色
Illumination:
above500LUX,whitelight
4.2.光源位置:
在檢查物品的正上方一公尺
Illuminantposition:
1meteraboveinspectionproduct
5.檢驗接受標準Acceptance:
依6.檢查標準內容數量檢驗。
FollowItem6.InspectionCriteriaquantityinspection.
6.檢查標準內容:
InspectionCriteria
6.1接受與拒絕標準(附表)
Accept/RejectCriteria
檢驗類別
InspectionItem
檢驗重點
InspectionPoint
判定依據
Criteria
使用工具
Tool
判定
Judgment
CR
MA
MI
a.外觀目檢
cosmeticinspection
IC本體標示
ICMarking
本體文字標品名,規格與實際所需料件不符者。
PS:
依item6.3.4.3作業
ChecktheMarked
shouldbemet
approvesheet.
pleasefollowitem6.3.4.3process
MicroScope
●
文字標示模糊不清或完全無法辨視者。
Bewareofthediscoloration,textofprintingorother
failures.(Ex.position,incorrectcontent&
lackofletter)
本體破損:
破損直徑在1㎜以上者。
如會影響元件功能者,不論破損直徑大小均不合格。
Within1mm,ifeffectthefunctionthatrejected.
IC本體
缺腳、斷腳者
Lackleadorbroken
(僅check需試驗的部份)
cosmeticinspection
沾錫性測試
(儘現貨市場IC需測)
Solderabilitytesting
(onlyforGreyMarket)
a.零件腳生鏽,經沾錫性模擬試驗後。
b.腳沾錫處無法連續覆蓋在95﹪以上者。
依item6.3.4.2作業
Thetestareashallbecoveredmorethan95%ofimmersedarea
withflashsolder.
pleasefollowitem6.5.4.2process
錫爐
b.MarkingCode
製造日期
ICMarkingCode
D/C必須要於2年內
依item6.2作業
D/Cshouldbewithin2years.
pleasefollowitem6.4process
C.功能
F/T
F/T功能測試
(onlyGreyMarket)
針對GreyMarketIC必須實際ONBOARDTest確認其品質
ONBOARDTEST
d.包裝Packing
IC包裝型式
Packingtype
其包裝可能為Reel、Tub或Tray,此部份依承認書作業
GreyMarket=現貨市場
6.2製造日期規範
MarkingCodecheck
針對製造MarkingCode必須要於2年內,如超過2年必須請供應商提
供出貨保證報告。
ChecktheMakingcodeshouldbewithin2years,iftheMaking
coveover2yearsthatsupplierguaranteeletterisnecessary.
6.3GreyMarket購入IC
GreyMarketIC
針GreyMarket所購入IC,必須依下列執行驗證
IftheICsourceisformGreymarketthatshouldbefollowingasbelow
itemtesting.
6.3.1採購單位必須於ERP備註欄位註明此ICsource為GreyMarket所購入。
PurchasingmustberecordtheICsource(“official”or”Graymarket”)inERPsystem.
6.3.2對於GreyMarketIC如採購單位可於入料前取得IC相關資料(如Item6.2),IQC將可先行比對判斷是否要允收。
IQCwillcheckthesourcecorrectornotbeforeincoming,ifPurchasingcangettheICphotoorpackinglabel.
6.3.3採購單位必須請供應商提供出貨保證報告,無Markingcode超過兩年。
Purchasingmustbeasksupplierprovidetheguaranteeletter,ifthemarkingcodeover2years.
6.3.4功能測試
Functiontest
6.3.4.1TestIC必須先過1次SMTReflow後,再onboardtest。
TestICmustbepasstheSMTreflowonetime.
a.BGAType:
針對BGATypeIC最少必須完成功能試驗2pcs含)以上。
ForBGAType,thefunctiontestquantityshouldbeover2pcs.
b.其他種類IC:
針對IC必須試驗至少5pcs(含)以上。
OthersIC,functiontestquantityshouldbeover5pcs.
6.3.4.2.沾錫性測試
Solderability
a.腳沾錫處必須續覆蓋超過95%以上。
●溫度SolderTemperature:
245℃±
5℃
●時間ImmersionPeriod:
5Sec
b.測試數量1pcs
TestQ’TY:
1pcs
6.3.4.3比對ICIQCDbase資料,確認下列訊息格式是否正確,並拍照記錄於IQCDbase內;
ChecktheICmarkingandpackinglabelshallbemetofficialformat.
a.外包裝(如下圖Filename:
Packing)
Packingmethod{seephoto(filename:
Packing)}
b.外包裝原廠Label,須含D/C、LotNo、生產地及數量(如下圖Filename:
ReelLabel2)
Thecontainershallbemarkedwiththepartnumber,description,lot/datenumber,manufacturername,quantityofcards,andIPC/JEDECJ-STD-033,includingrevisionlevel.
c.外包裝供應商Label(如下圖Filename:
ReelLabel)(無則可免除)
Packinglabelofsupplier{seephoto(filename:
RReelLabel)}
d.IC本體,含MarkingCode、IC所有印刷字樣,如為真空包,不需記錄(如下圖Filename:
IC本體)
ICMarking:
recordmarkingcodeandlotnoandD/C{seephoto(filename:
ICbody}.
6.3.5所有資料將保存於公司SERVER/品保處/IQC/IC檢驗資料。
AllofdatashouldberecordonBitaQAserver,asfollowing
6.4濕度敏感等級確認
MoistureSensitivityLevels(MSL)
6.4.1依下表”防潮真空包需求表”規定針對不同MSL等級及幫裝要求將不同,如MSL等級為2以上(含)一率必須真空包,並確認其濕度紙是否於規格內。
『濕度敏感等級』MSL,由小排到大,數字越小的表示其抗濕度能力越好;
數字越大的,表示其可以暴露於環境濕氣的時間要越短。
Pleasefollowasbelowtable”DryPackingRequirements
”tocheckthepackingmethod,IftheMSLNois2-6,theICshouldbeDrypack,andcheckthehumidityindicatorshallbeunderspec.
Table1.防潮真空包需求表DryPackingRequirements
MSLLevel
MSL等級
DryBeforeBag
真空包裝
MBBwithHIC
使用防潮袋並含濕度指示卡
Desiccant
乾燥劑(包)
MSID*Label
防濕警告標準
CautionLabel
警告標籤
1
Optional
非必需
NotRequiredifclassifiedat220°
C-225°
C
Required**ifclassifiedatotherthan220°
如分類於220°
C不需要
如分類不是於220°
C則需要
2
Required
必需
2a-5a
6
6.4.2依照表1規定,如該IC包裝必須包含濕度指示卡,請依下列方式確認該濕度是否於規定內。
AsfollowTable1requirement,pleasefollowasbelowmethodtochecktheHICstatus。
Table2濕度指示卡比較判別表TypicalHICSpotCompliance
Indication
at2%RH
Environment
濕度為2%
at5%RH
濕度為5%
at10%RH
濕度為10%
at55%RH
濕度為55%
at60%RH
濕度為60%
at65%RH
濕度為65%
5%
Spot
Blue藍色
(dry乾燥)
Lavender
(spotvalue)
change≧7%hue
淡紫色≧7%
Pink粉紅色
(wet潮溼)
10%
change10%≧hue
淡紫色≧10%
60%
change≧10%hue
6.4.3Level1需求
Level1Requirements
MSL等級為1之IC,如其reflow溫度於220°
C之外,及必須標示警告其最大溫度於防潮袋上,並易於便讀。
Level1partsclassifiedforotherthan220°
CmaximumreflowtemperatureshallhaveaCautionlabelwiththemaximumreflowtemperaturespecified.TheCautionlabelshallbeaffixedtotheMBB(ifused)ortothelowest-levelshippingcontainer.TheCautionlabelwillnotberequiredifa“BarCode”labelincludestheLevel1classificationandmaximumreflowtemperatureinformationinhumanreadableform.Level1partsclassifiedat220°
Cmaximumreflowtemperaturedonotrequireanymoisturerelatedlabels.
6.4.4防潮真空包裝確認
MoistureBarrierBagSealing
此防潮袋必須經熱壓封口,不可有破洞或漏氣狀況;
袋內必須抽真空,但不可過度造成損傷包裝內IC或包裝材變型。
ThebagshouldbeheatsealedsoasnottodamageorcausedelaminationoftheMBB.Fullairevacuationisnotneededorrecommended;
lightairevacuationwillreducethepackagingbulkandenhancecartonpacking.ExcessiveevacuationmayimpededesiccantperformanceandleadtoMBBpunctures.
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- B3QA068ICSIP 进料 检验 规范
![提示](https://static.bdocx.com/images/bang_tan.gif)