ansys平面结构强度分析实例Word下载.docx
- 文档编号:20041314
- 上传时间:2023-01-16
- 格式:DOCX
- 页数:9
- 大小:120.69KB
ansys平面结构强度分析实例Word下载.docx
《ansys平面结构强度分析实例Word下载.docx》由会员分享,可在线阅读,更多相关《ansys平面结构强度分析实例Word下载.docx(9页珍藏版)》请在冰豆网上搜索。
1)选择单元类型
运行Preprocessor>
ElementType>
Add/Edit/Delete,弹出ElementTypes对话框,单
击Add,弹出LibraryofElementTypes窗口,选择StructuralSolid,输入82,单击OK。
在ElementTypes对话框中,单击Options,在弹出的对话框中,设置K3选项栏为Plane
strsw/thk,设置K5选项栏为Nodalstress,设置K6选项栏为Noextraoutput。
表示单元
是应用于平面应力问题,且单元是有厚度的。
2)定义实常数
RealConstants>
Add/Edit/Delete,弹出RealConstants对话框,
点击Add,在弹出的对话框中点击OK,弹出RealConstantsSetNumber1,forPLANE82
对话框,在THK选项栏中设置板厚度为0.005m。
设置完毕单击OK按钮。
(3)设置材料属性
MaterialProps>
MaterialModels,在弹出的对话框中依次双击
Structural,Linear,Elastic,Isotropic,弹出LinearIsotropicPropertiesforMaterialModel
1对话框,在EX选项栏中设置数值2.1e11,在PRXY选项栏中设置数值0.3。
设置完毕单击OK按钮。
4)建立模型
Modeling>
Create>
Area>
Polygon>
ByVertices
框,选项栏中依次填写下表中数据,单击Apply,完成后单击OK。
次数
坐标(m)
1
0,0,0
2
0,0.15,0
3
0.1215,0.15,0
4
0.243,0.15,0
5
0.243,0.1,0
6
0.149,0.1,0
7
0,0,0
继续运行Preprocessor>
Circle>
SolidCircle,得到下图所示对
话框,输入表中数据,设置完毕点击OK按钮。
WPX(m)
WPY(m)
Radius(m)
0.05
0.1
0.027
0.196
0.125
0.015
进行布尔运算:
Preprocessor>
Operate>
Booleans>
Subtract>
Areas,先选矩
形面单击OK,再单击圆面,单击OK。
重复两次得到下图所示图形。
5)划分网格
运行Meshing>
SizeCntrls>
ManualSize>
Areas>
AllAreas,弹出下图所示对话框,在
SIZE选项栏中填写0.005,点击OK按钮。
运行Mesh>
MeshTool,弹出下图所示对话框,在Shape选项栏后面,选择Tri和Free,单击Mesh.划分网格,网格划分结果如下。
MeshTool
ElementAttributes:
|Global
Set|
I-SmartSize
d
FineG
2J
Coarse
SizeControls:
GlobalSM
□ear|
Areas
$et
Clear|
Lines
Clear1
Copy|
Flip|
Layer
Keypts
Me$h:
1Areas
J
Shape:
GTri,
「Mapped「
'
Quad
Sweep
3or4sided
MeshClear
Refineat:
|Elements▼|
Refine
CloseIHelp
6)施加约束
Lines,选择最
选择菜单Solution>
DefineLoads>
Apply>
Structure>
Displacement>
On
左边的垂直边,弹出下图所示对话框,选择AllDOF,单击OK。
7)施加载荷
Structure>
Pressure>
OnLines
示对话框。
拾取最上面两条水平边的右面一条,单击OK按钮。
弹出如图4-25所示对话框。
在VALUE选项栏中填写24.3KN/m。
设置完毕点击OK完成设置。
AApplyPRESonlines
Constantvalue
[SFL]ApplyPRESonlinesasa
IfConstantvaluethen:
VALUELoadPRESvalue24.3
ofline
OptionalPRESvaluesatendJ(leaveblankforuniformPRES
Value
OKIApply
Cancel
Help
(8)求解
运行Solution>
Solve>
CurrentLS,弹出下图所示对话框。
单击OK按钮,开始计算,
计算结束会弹出计算完毕对话框,单击Close关闭对话框,计算完毕。
(9)后处理
运行GeneralPostproc>
PlotResults>
ContourPlot>
NodalSolu,弹出下图所示对话
框,运行DOFSolution>
Displacementvectorsum和Stress>
vonMisesstress,分别显示
长方形面板的位移云图和应力云图。
结果显示如下。
应力的最大值为439.453kPa。
AContourNodalSolutionData
Iten.tobecontoured
由Favorites
NodalSolution
Ifllafiifilaa
-DOFSolution
Stress
TotalMechanicalStrain
ElasticStrain
PlasticStrain
CreepStrain
MThermalStrain
TotalMechanicalandThermalStrain
GSwellingstrain
rEnergy
i3FailureCriteria
佥BodyTemperatures
Undisplacedshapekey
Undisplacedshapekey|Deformedshapeonly3
ScalefactorAutoCalculated:
Additiona]Options®
|
0Kj刖plyICancelIHeb
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ansys 平面 结构 强度 分析 实例