大西M6000上线测试报告Word格式文档下载.docx
- 文档编号:19921169
- 上传时间:2023-01-12
- 格式:DOCX
- 页数:24
- 大小:24.49KB
大西M6000上线测试报告Word格式文档下载.docx
《大西M6000上线测试报告Word格式文档下载.docx》由会员分享,可在线阅读,更多相关《大西M6000上线测试报告Word格式文档下载.docx(24页珍藏版)》请在冰豆网上搜索。
2.路由测试
2.1静态路由
2.1.1静态路由的基本功能
验收项目
验证M6000产品静态路由的基本功能
测试环境
预置条件
测试路由器和大西M6000背靠背连接正确。
测试路由器和大西M6000的相连端口配置正常的IP地址,互相正常ping通。
测试过程
1.在测试路由器上配置接口IP和一个loopback1接口IP,配置到M6000loopback1地址的静态路由。
interfaceGigabitEthernet0/0
undoshutdown
ipaddress192.168.1.1255.255.255.0
interfaceLoopBack1
ipaddress1.1.1.1255.255.255.255
iproute-static678.217.167.17255.255.255.255192.168.1.2
2.在大西M6000上配置接口IP和一个loopback1接口IP,配置到测试路由器loopback1地址的静态路由。
interfacegei-0/0/1/2
noshutdown
ipaddress192.168.1.2255.255.255.0
interfaceloopback1
ipaddress678.217.167.17255.255.255.255
iproute1.1.1.1255.255.255.255192.168.1.1
预期结果
1.使用showipforwardingroutestatic能够看见建立的静态路由;
2.在大西M6000上能ping通测试路由器的loopback1地址。
与预期一样。
备注
2.1.2静态路由preference的调整
验证M6000产品静态路由优先级功能
两台设备完成2.1.1静态路由测试项配置的接口IP地址。
1.在M6000上配置静态路由。
iproute1.1.1.1255.255.255.255192.168.1.1metric150/*更改metric为150*/
1.使用showipforwardingroutestatic能够看见建立的静态路由且metric为150。
2.2动态路由协议
2.2.1M6000的ISIS协议基本测试
测试项目
M6000ISIS协议的基本功能
.....
1.大西M6000和大西T1200连接正确。
2.大西T1200和大西M6000的相连端口配置正常的IP地址,互相正常ping通。
1.配置大西T1200设备的ISIS数据:
[T1200]
interfacegei_5/10
physical-layermodebutx
ipaddress218.65.173.161255.255.255.252
out_index33
hybrid-attributefiber
negotiationauto
iprouterisis
isiscircuit-typelevel-2-only
isisnetworkpoint-to-point
mplsip
protectinterfacetoken400
2.配置大西M6000设备的ISIS数据:
[M6000]
interfaceloopback1
interfacegei-0/0/1/1
ipaddress218.65.173.162255.255.255.252
routerisis
area86.4640.0771
system-id6782.1716.7017
is-typelevel-2-only
distance115
metric-stylewide
set-overload-biton-start-up180
maximum-paths8
interfacegei-0/0/1/1
circuit-typelevel-2-only
networkpoint-to-point
metric1level-2
3.然后在M6000上使用showisisadjacency,查看邻居状态。
可以看到M6000的isis邻居关系正常建立。
2.2.2M6000BGP协议基本功能测试
测试目的
验证M6000的BGP协议基本功能测试
......
M6000完成2.2.1测试项的相关配置。
1.M6000上的配置:
routerbgp8090
nosynchronization
bgprouter-id678.217.167.17
redistributeconnected
redistributestatic
network218.65.173.176255.255.255.248
neighbor678.217.167.1remote-as8090
neighbor678.217.167.1activate
neighbor678.217.167.1next-hop-self
neighbor678.217.167.1passwordencryptedJMPSqHLDVQcIpgcZS3okf1fA0ko155UOnfKANfLNHtNM5Ke/gk4knffZq+6JuWge4mdiwg0c6SmWuPwsi6JYlhqm
ncXlcQTmWl0ztn3neiU=
neighbor678.217.167.1update-sourceloopback1
neighbor678.217.167.2remote-as8090
neighbor678.217.167.2activate
neighbor678.217.167.2next-hop-self
neighbor678.217.167.2passwordencryptedJMPSqHLDVQcIpgcZS3okf1fA0ko155UOnfKANfLNHtNM5Ke/gk4knffZq+6JuWge4mdiwg0c6SmWuPwsi6JYlhqm
neighbor678.217.167.2update-sourceloopback1
2.民族NE5000E:
bgp8090
peer678.217.167.17as-number8090
peer678.217.167.17grouppgBRAS
peer678.217.167.17bfdenable
ipv4-familyunicast
peer678.217.167.17enable
3.琅东NE5000E:
4.然后在M6000上用showipbgpneighbor观察邻居状态是否正常;
邻居状态正常
2.2.3M6000BGP协议MD5加密功能测试
验证M6000的BGP协议邻接体建立MD5加密功能
完成2.2.2M6000的BGP协议基本测试项的BGP相关配置。
1.NE5000E
2.大西M6000上的配置
neighbor678.217.167.1passwordencryptedJMPSqHLDVQcIpgcZS3okf1fA0ko155UOnfKANfLNHtNM5Ke/gk4knffZq+6JuWge4mdiwg0c6SmWuPwsi6JYlhqm
neighbor678.217.167.2passwordencryptedJMPSqHLDVQcIpgcZS3okf1fA0ko155UOnfKANfLNHtNM5Ke/gk4knffZq+6JuWge4mdiwg0c6SmWuPwsi6JYlhqm
3.在M6000上观察邻居状态是否正常;
4.在大西M6000上更改密码后测试邻居关系。
5.恢复密码
1.步骤4中邻居关系异常。
2.步骤5中邻居关系正常。
2.2.5M6000BGP协议路由发布测试
验证M6000的BGP协议路由发布
1.在大西M6000上发布用户路由至BGP:
network218.65.173.176255.255.255.248
iproute218.65.173.176255.255.255.248null180
2.在NE5000E上使用displayiprouting-table218.65.173.176查看是否有路由条目。
在NE5000E上能看到其收到218.65.173.176/29的BGP路由
3.MPLS测试
3.1MPLSLDP测试
MPLSLDP测试
验证M6000产品LDP协议的基本功能
完成2.2.1M6000的ISIS协议基本测试项的ISIS相关配置。
测试步骤
1.在M6000和T1200上将互连端口的LDP打开:
mplsip
【M6000】
mplsldpinstance1
router-idloopback1
access-fechost-route-only
2.在M6000上查看LDP邻居的建立和标签分配情况。
1)用showmplsldpneighborinstance1查看邻居的建立情况;
2)用showmplsforwarding-table查看标签分配情况。
1.M6000和T1200间能够建立LDP邻居;
2.查看通过LDP建立的MPLS转发表。
正常。
4.NTP功能
4.1NTP功能
验证M6000产品NTP
验证M6000产品NTP功能正常
1.需要配置NTPServer;
2.确保路由器到NTPServer可达。
1.配置NTPServer的地址和功能;
2.ntpserverx.x.x.xpriority1version3在M6000上配置指定NTPServer的地址;
看到NTP处于同步状态后,M6000的系统日期和时间转变为相同的NTPServer的系统日期和时间。
5.业务测试
5.1静态用户
静态用户接入测试
1.验证M6000的基本接入功能;
2.验证M6000产品引擎切换对业务的影响。
...........
1、设备连接正确
2、两台设备完成2.2.3配置
1、在M6000配置;
1.配置地址池
interfacevbui1
ipaddress218.65.173.177255.255.255.248
!
vbui-configuration
interfacevbui1
ip-poolpool-namepppoe-1pool-id1
ipoe-dns-server202.103.224.68
ipoe-dns-server202.103.225.68second
member1
start-ip218.65.173.178end-ip218.65.173.182
static-ip218.65.173.182
$
ip-host218.65.173.182gei-0/0/1/2.4092vlan4092
2.接口
interfacegei-0/0/1/2.4092
vcc-configuration
interfacegei-0/0/1/2.4092
encapsulationip-over-ethernet
vlan-configuration
encapsulation-dot1q4092
3.配置静态用户
2、测试交换机上配置;
Vlan1000
nametest
interfaceGigabitEthernet7/1/1
portlink-typetrunk
undoporttrunkpermitvlan1
porttrunkpermitvlan1000
speed1000
duplexfull
interfaceGigabitEthernet3/1/36
portaccessvlan1000
3、在PC上配置
配置IP地址218.65.173.182
笔记本能能上网
笔记本能能ping通网关;
并能上网。
5.2校园网宽带PPPOE
2、两台设备完成2.2.3、5.1配置
1.配置认证方案
aaa-authentication-template6
aaa-authentication-typeradius
authentication-radius-group6
3.配置计费方案
aaa-accounting-template6
aaa-accounting-typeradius
accounting-radius-groupfirst6
4.配置radius组
radiusauthentication-group6
server1202.103.194.199keytroytroyport1814
server2202.103.194.198keytroytroyport1814
nas-port-id-formatclass2
deadtime1
nas-ip-address678.217.167.17
radiusaccounting-group6
server1202.103.194.199keytroytroyport1815
server2202.103.194.198keytroytroyport1815
nas-ip-address678.217.167.17
local-bufferenable
5.配置域
domain57
bindauthentication-template6
bindauthorization-template6
bindaccounting-template6
aliascampus-pppoe
6.配置pppox模板
subscriber-manage
pppox-cfg1
pppauthenticationpap
pppkeepalivetimer60count4
pppquick-redialenable
$
7.接口
interfacegei-0/0/1/2.4093
pppoxtemplate1
bindsal2
encapsulationppp-over-ethernet
user-dynamic-vlanany-other-dot1q
encapsulation-dot1qrange4093
3、在PC上的PPPOE客户端输入测试用户进行拨号;
笔记本拨号能获取到IP地址并能ping通网关;
能打开网页。
1.笔记本拨号能获取到IP地址并能ping通网关;
2.能打开网页
5.3普通宽带PPPOE
普通宽带PPPOE测试
aaa-authentication-template1
authentication-radius-group1
2.配置计费方案
aaa-accounting-template1
accounting-radius-groupfirst1
radiusauthentication-group1
server1202.103.194.201keytroytroyport1812
server2202.103.194.205keytroytroyport1812
server3202.103.194.207keytroytroyport3799
server4202.103.194.210keytroytroyport3799
radiusaccounting-group1
server1202.103.194.201keytroytroyport1813
server2202.103.194.205keytroytroyport1813
domain1
bindauthentication-template1
bindauthorization-template1
bindaccounting-template1
aliaspppoe
6.接口
bindsal1
2、在PC上的PPPOE客户端输入测试用户进行拨号;
2.能打开网页。
2.主备引擎切换时笔记本丢2个包。
5.4MPLSVPN测试
MPLSVPN测试
验证M6000产品MPLSVPN功能
.........
1.大西T1200和大西M6000连接正确。
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- M6000 上线 测试报告