ASTM标准F1856碳粉消耗量测试方法.docx
- 文档编号:315452
- 上传时间:2022-10-08
- 格式:DOCX
- 页数:7
- 大小:16.34KB
ASTM标准F1856碳粉消耗量测试方法.docx
《ASTM标准F1856碳粉消耗量测试方法.docx》由会员分享,可在线阅读,更多相关《ASTM标准F1856碳粉消耗量测试方法.docx(7页珍藏版)》请在冰豆网上搜索。
ASTM标准F1856碳粉消耗量测试方法
StandardPracticefor
DeterminingTonerUsageforPrinterCartridges1
《判定打印机碳粉消耗量的标准方法》
1.Scope
1.使用范畴
1.1Thispracticecoversaproceduretodeterminetheweightoftonerusedforprintingasinglepagederivedfromanelectrophotographicprocess.Thepracticeusesaprintertexttargetspecificallydevelopedforeachprinterforapagecoverageof560.5%oftheprintablearea.Thispracticerequiresspecifictoolsandskillsfordisassemblingandreassemblingprintercartridges.
1.1此标准涵概了,激光打印机在输出一页文档时,测量碳粉消耗量的程序步骤。
此方法操作规定每台打印机使用指定的打印文档,且输出文档的页覆盖率为5±0.5%。
执行操作时,需要特定的测试工具,且具备拆卸、重新组装碳粉盒的能力。
1.2Thevaluesstatedininch-poundunitsaretoberegardedasthestandards.TheSIunitsgiveninparenthesesareforinformationonly.
1.2标准中数值的单位是英寸—镑。
括号里的SI单位仅做参考。
1.3Thisstandarddoesnotpurporttoaddressallofthesafetyconcerns,ifany,associatedwithitsuse.Itistheresponsibilityoftheuserofthisstandardtoestablishappropriatesafetyandhealthpracticesanddeterminetheapplicabilityofregulatorylimitationspriortouse.
1.3此标准主旨不是罗列所有的安全因素,而是联合它们的使用。
此标准的使用人
有责任建立可靠适用性、健全的测试方法,并检测改进措施的适用性。
2.ReferencedDocuments
2.涉及文件
2.1ASTMStandards:
2
F335TerminologyReferringtoElectrostaticCopying
2.1ASTM标准F335《静电复印的相关术语》
3.Terminology
3.术语
3.1DefinitionsofTermsSpecifictoThisStandard:
3.1标准中特定术语的解释
3.1.1tonerusage—amountoftoner(milligramsperprint)removedfromthetonerhopperduringtheprintingofonepage.
3.1.1碳粉消耗量:
打印机打印一页文档时,从碳粉仓所使用的碳粉数量(毫克/页)。
4.SummaryofPractice
4.惯例摘要
4.1Anelectrophotographicprinterutilizinganall-in-onesupplycartridgeissetuptodeterminethetonerusedforasinglepageofprint.Atestpagewith560.5%textprintoutputforthecontrolcartridgeisused.5%textcoverageoftheprintableareaistheindustryacceptedaveragepagecoverageforofficeprinters.Theall-in-onecartridgeisdisassembledtoseparatethetonerhopperfromthewastetonercollectionbin.Theweightofthefulltonerhopperismeasured.Aspecifiednumberofprintsarecreatedontheprinterusingthiscartridgeandtheweightoftheusedtonerhopperismeasured.Thetonerusedforoneprintiscalculated.Inaddition,theresultscanbeusedtoestimatethetotalpageyieldofthetonercartridge.Acomparisoncanbemadebetweenthetonerusedforthecontrolcartridgeandanyothercartridgetestedusingthispractice.
4.1准备一台已安装好一体式碳粉盒的激光印机,用来评测单页打印碳粉消耗量。
覆盖率为5±0.5%的文本测试页。
5%的文档覆盖率是行业公认的办公打印平均覆盖率。
一体式碳粉盒的粉仓可以从废粉仓中分离出来。
先测量碳粉盒满粉仓的初始重量,打印一定数量后,再称重此粉盒粉仓的重量。
即可算出打印的粉耗量。
另外,可使用此粉耗量估测出整个碳粉盒的总页产量。
使用此方法也可进行碳粉盒间的对比测试。
5.SignificanceandUse
5.使用意义
5.1Thispracticecanbeusedfortheevaluationofnewandremanufacturedtonercartridgesandtheirrespectivecomponentsusedinanelectrophotographicprocess.
5.1此方法可用于评估用于相同激光打印机的新碳粉盒和再填充碳粉盒。
5.2Thistestissuitableforresearchanddevelopment,andqualityacceptanceevaluations.
5.2此测试适用于新品开发和质量评估。
6.Interferences
6.干扰因素
6.1Relativehumiditycanimpacttestresults.Thetestshouldbeperformedatacontrolledtemperatureandhumiditywithintheoperatinghumidityrangeoftheprinter.Thisisusuallybetween20and80%RH.Allequipment,andmaterialsshouldbeconditionedinthesametemperatureandrelativehumidityforatleast24hpriortotesting.
6.1相对湿度可能影响实验结果。
测试需要在把温度和湿度控制在打印机运行所允许的湿度范围内进行,通常定为20和80%R。
H在测试之前,所有的设备和物料必须在此环境中放置至少24个小时。
6.2Incomparativecartridgetestthesametesttarget(data)andprintermustbeused.Thenumberofcharactersandthetypeofcharacters,fontandfontsizehaveadirectaffectontonerconsumption.
6.2碳粉盒对比测试必须使用相同的测试样张和打印机,字符的数量和字符种类,字体和字体大小都对碳粉消耗有直接影响。
6.3Thetestpatternshouldnotproduceunevenwearonthecartridgecomponentsasthiswillaffectthetestresults.
6.3粉盒部件的磨损会导致测试样张打印不均匀,这样会影响测试结果。
6.4Printerrelateditemssuchasthepowersupply,densitycontrolsettings,resolutionenhancements,tonersaversettings,economymodesettings,andlaseropticsmayimpactimagequalityandtonerconsumption.
6.4打印机相关的事项如:
电源,密度设置,增强分辨率,节粉设置,经济模式设置和激光都可能影响输出图像质量和粉耗量。
6.5Testprintersshouldbeingoodmechanicalandelectricalcondition.Preferably,printerswithacontinuoushistoryofpreventativemaintenanceshouldbeused.Anyprinterfailurescaninvalidatethetest.
6.5测试打印机应处于良好状态。
最好使用有进行持续维护的打印机。
打印机出现
任何故障都会使测试无效。
6.6Acalibratedbalancemustbeusedtoobtainweights.
6.6使用校正过的秤进行称重。
6.7Thetechniquesusedforcartridgedisassemblyshouldavoidtonerspillageandensureaccuratetonerweightmeasurements.
6.7拆卸碳粉一定避免碳粉溢出,以保证准确的碳粉重量测量。
7.EquipmentandMaterials
7.设备和物料
7.1ElectrophotographicTestPrinter,suitablefortestingpurposes.
7.1符合测试要求的激光打印机
7.2PrinterDataSystem,capableofsupplyinga560.5%textpageforthespecifictestprinterbasedonthecontrolcartridge(averageoriginalprintermanufacturer'scartridge).This560.5%testtargetdatac
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTM 标准 F1856 碳粉 消耗量 测试 方法
![提示](https://static.bdocx.com/images/bang_tan.gif)