冷轧钢带表面检查线缺陷检查综述.docx
- 文档编号:30241255
- 上传时间:2023-08-13
- 格式:DOCX
- 页数:22
- 大小:1.24MB
冷轧钢带表面检查线缺陷检查综述.docx
《冷轧钢带表面检查线缺陷检查综述.docx》由会员分享,可在线阅读,更多相关《冷轧钢带表面检查线缺陷检查综述.docx(22页珍藏版)》请在冰豆网上搜索。
冷轧钢带表面检查线缺陷检查综述
表面检查线缺陷检查
InspectionLineSurfaceDefectChecking
钢带轧制表面缺陷分析
CatalogueofSurfaceDefects
TextureRolledSteelStrip
缺陷目录
Indexofcontents
1.Scratches,longitudinal纵向擦伤2
2.Scratches,transversal横向擦伤3
3.Grooves凹痕4
4.Remainsofquenchingmedium淬火介质残留5
5.Pimples(rolldefect)钢带表面皮疹(轧辊缺陷)6
6.Scales(rolldefect)刻痕(轧辊缺陷)7
7.Rollingmarks,transversallines轧印,横向轧线8
8.Rollingmarks,crossdefect轧印,交叉类型9
9.Chattermarks振颤印10
10.Rokes纵裂纹11
11.Shell剥落12
12.Holes孔洞13
13.Inrolledexternalparticles杂质轧入14
14.Scratcheswithinternalcracks内裂纹滑痕15
15.Grindingmartensite抛光状马氏体16
Typeofdefect(缺陷类型)
Scratches,longitudinal纵向擦伤
Definition说明
Surfacedefectsinrollingdirection.
沿轧制方向产生
Appearance缺陷形貌
Defectsinrollingdirectionofvarioussizes,whichareeitheropenorclosed.
缺陷沿轧制方向产生,有各种尺寸,缺陷形式可能是开放的或封闭的
Picture缺陷照片
V=6.3:
1
Rmax=6.55µm
Causeofdefect缺陷成因
Defectscanoccurinmostproductionstepsofcoldrolling,duetorunningstripoveredgesorridgesofmachinepartsorpre-stripper(overrolledparticlesinguidesetc).
在冷轧生产的各个环节都可能产生该种缺陷,比如钢带的利边、设备的棱角或钢带导位上的小杂质都可能造成该缺陷。
Acceptance检验
Defectisacceptedifitoccursonlypartiallyinaccordancewithspecifiedroughness(analogtofinegrooves).
如果缺陷的粗糙度与材料正常部分粗糙度一致的话,可以接受(例如小的刻痕)。
Sorbitex75-Rtmax.3µminthickness<=0.15mmand5µminthickness>0.15mm
厚度0.15mm以下的材料粗糙度可接受范围Rtmax.3µm,厚度大于0.15mm以上材料,粗糙度可接受范围Rtmax.5µm
Sorbitex80/90-Rtmax.3µminthickness<=0.60mmand5µminthickness>0.60mm
厚度0.60mm以下的材料粗糙度可接受范围Rtmax.3µm,厚度大于0.60mm以上材料,粗糙度可接受范围Rtmax.5µm
Typeofdefect(缺陷类型)
Scratches,transversal横向擦伤
Definition说明
Surfacedefectsacrossrollingdirection.
与轧制方向垂直
Appearance缺陷形貌
Defecttransversalorcrosswisetorollingdirectionindifferentsizes,openorclosed.
缺陷沿轧制方向垂直方向产生,有各种尺寸,缺陷形式可能是开放的或封闭的
Picture缺陷照片
V=6.3:
1
Rmax=1.07µm
Causeofdefect缺陷成因
Possibletooccurinnearlyallproductionstepsofcoldrolling.
Arisingmostlybystripslippingcrosswiseovermetalrolls,soiledstrippersorrelativemovementsbetweensingleturnsofthecoil.
在冷轧的各个环节都可能产生该缺陷。
特别是当钢带呈松弛状态经过轧辊、不干净的分离器以及此时钢卷各层间产生相对滑动时,容易产生上述缺陷。
Acceptance检验
DefectacceptableuptoroughnessofRtmax.1.0µmifnotsharpedgedinmagnificationof100:
1.
在放大100倍未见利边且粗糙度最大Rtmax.1.0µm时,可以认为合格。
Typeofdefect(缺陷类型)
Grooves凹痕
Definition说明
Fineabrasionofsurfaceinrollingdirection
沿轧制方向的细小磨痕
Appearance缺陷形貌
Defectinrollingdirection,usuallycontinuoussurfacedefectswhichareopenorclosed.
沿轧制方向经常连续出现,缺陷形式可能是开放的或封闭的
Picture缺陷照片
Causeofdefect缺陷成因
Defectiscausedmostlybyparticlesofdirtorchipsinstripperorstrippress
该缺陷主要由于小污物或小的金属碎片造成
Acceptance检验
Defectisacceptedifitoccursonlypartiallyinaccordancewithspecifiedroughness.
如果缺陷仅在局部产生同时粗糙度能满足要求就判定为合格
Sorbitex75-Rtmax.3µminthickness<=0.15mmand5µminthickness>0.15mm
厚度0.15mm以下的材料粗糙度可接受范围Rtmax.3µm,厚度大于0.15mm以上材料,粗糙度可接受范围Rtmax.5µm
Sorbitex80/90-Rtmax.3µminthickness<=0.60mmand5µminthickness>0.60mm
厚度0.60mm以下的材料粗糙度可接受范围Rtmax.3µm,厚度大于0.60mm以上材料,粗糙度可接受范围Rtmax.5µm
Typeofdefect(缺陷类型)
Remainsofquenchingmedium
淬火介质残留
Definition说明
Inrolledremainsofquenchingmedium.
轧制后淬火介质残留
Appearance缺陷形貌
Greypartsonsurfaceinlongitudinaldirectionindifferentgrades.Clearopticaldifferencetobasicsteelmaterial.
钢带表面沿轧制方向的不同层次的灰白色区域。
用光学检查即可清除的与钢基体进行区分。
Picture缺陷照片
V=6,3:
1
Causeofdefect缺陷成因
Causedduetoanon-optimalstrippingofquenchantafterheattreatmentinliquidmetalbathandheavytexturecoldrollingafterwards.
该缺陷的主要成因在于钢带进行淬火冷却过程中,淬火介质在钢带表面残留
Acceptance检验
DefectoccursinrarecasesandisacceptableuptoroughnessofRtmax.3.0µm:
该缺陷零星产生时,如果缺陷区域表面粗糙度小于Rtmax.3.0µm则判定为合格
Typeofdefect(缺陷类型)
Pimples(rolldefect)
钢带表面皮疹(轧辊缺陷)
Definition说明
Peaksonstripsurface.
钢带表面凸起。
Appearance缺陷形貌
Raisedareasofdifferentlook,periodicallyoccurringonthestripsurface.
在钢带表面周期性出现,成不同表象的凸起状态。
Picture缺陷照片
V=6,3:
1
Causeofdefect缺陷成因
Originatedbysmalloutbreaksordepressionsonthesurfaceofworkingrolls.
工作辊上的小破损或局部压溃将造成此类缺陷。
Acceptance检验
OverrolledandonlyopticaldefectsuptoØ2mmareaccepted.
单个缺陷的直径经测量直径小于2mm认为合格。
DefectsØ>2mmshallbeacceptedifdefect-quotadoesnotexceed2x8mmperdeliveredcoil.DefectshavetobemarkedbyC.D.Wälzholz.
如果单个缺陷尺寸大于2mm但每卷钢带中缺陷不超过2x8则认为钢带合格。
但缺陷部分必须由C.D.Wälzholz.公司进行标记。
Typeofdefect(缺陷类型)
Scales(rolldefect)
刻痕(轧辊缺陷)
Definition说明
Scalesareoutbreaksofareasofmatteroftheworkingroll.
主要由于轧辊材质缺陷造成
Appearance缺陷形貌
Regularrecurringseveremarksofdifferentsizeandmanner.
有规律出现但形状和尺寸没有规律
Picture缺陷照片
V=6,3:
1
Causeofdefect缺陷成因
Scalesareoutbreaksinareasoftheworkingroll.
工作辊局部区域破损造成。
Acceptance检验
Defectisacceptediflotdoesnotexceed2x8mmbycoil.Defectshavetobemarked.
整卷的缺陷不超过2x8mm认定合格。
缺陷必须标识出来。
Typeofdefect(缺陷类型)
Rollingmarks,transversallines
轧印,横向轧线
Definition说明
Transversaldefectsareshortrollmarksacrosstherollingdirection.
横向轧印是短的垂直于轧制方向
Appearance缺陷形貌
Regularrecurring,narrowlinearmarksacrossrollingdirection.
周期性出现,窄的线性形状并垂直于轧制方向
Picture缺陷照片
V=6.3:
1Rmax=1.01µm
Causeofdefect缺陷成因
Defectiscausedbyfinebreaksonsurfaceofworkingroll,i.e.defectiveworkingroll.
该类缺陷是由于工作辊上的细小破损造成的例如有缺陷的工作辊。
Acceptance检验
DefectisaccepteduptoroughnessofRtmax.1.0µm,whennotsharpedgedinmagnification100:
1.
按100:
1比例放大未见利边的情况下,粗糙度小于Rtmax.1.0µm判定合格。
Defectwithroughness>Rt=1.0µmisonlyacceptedifdefect-quotadoesnotexceed2x8mm.Defectshavetobemarked.
如果缺陷的粗糙度大于Rt=1.0µm那么在整卷缺陷小于2x8mm时仍可判定为合格。
但必须讲缺陷标记出来。
Typeofdefect(缺陷类型)
Rollingmarks,crossdefects
轧印,交叉类型
Definition说明
Transversalrollingdefectsarelongitudinal,mostlyvisualmarksacrossrollingdirection.
横向的轧制缺陷是纵向形式的,沿轧制方向产生交叉类型缺陷
Appearance缺陷形貌
Periodicallyoccurring,longitudinalmarksofdifferentlengthacrossrollingdirection.
Length>2x8mmdefectwidth.
周期性出现,交叉于轧制方向不同长度的纵向轧印。
缺陷的长度大于2x8mm宽度
Picture缺陷照片
V=6.3:
1
Rmax=1.02µm
Causeofdefect缺陷成因
Defectonworkingrolloccursduetocontactwithothermachinerypartswhenequippingthemill.
在轧机装辊时或与其它设备连接过程中,工作辊产生损伤造成上述缺陷。
Acceptance检验
DefectsuptoroughnessRtmax.1.0µmisaccepted,iftherearenosharpedgesinmagnification100:
1.
按100:
1的比例放大未见利边的情况下,缺陷处的粗糙度最大为Rtmax.1.0µm。
Typeofdefect(缺陷类型)
Chattermarks振颤印
Definition说明
Wavelikeappearancesonsurface.
与轧制方向垂直产生的表面波浪印记
Appearance缺陷形貌
Undulationsacrosstorollingdirectionoverthetotalwidthofthestrip.
贯穿整个钢带宽度与轧制方向垂直的波浪印记
Picture缺陷照片
Causeofdefect缺陷成因
Duetonot100%accurategrindedworkingrolls.
由于工作辊没有100%达到磨削精度造成此类缺陷
Acceptance检验
ReleaseonlyafterconsultationwithqualitymanagementKWBresp.customer.
需要质量控制部门和用户共同商议决定
Typeofdefect(缺陷类型)
Rokes纵裂纹
Definition说明
Longitudinalmarksparalleltorollingdirection.
与轧制方向平行的纵向缺陷
Appearance缺陷形貌
Narrow,longitudinalmarks,inrollingdirection,lighterordarkerthansteelsurface.Rokesdonotappearregularandarelimited.
缺陷比较狭窄,沿轧制方向,颜色比钢带表面颜色深或浅。
纵裂纹的出现是没有规律的。
Picture缺陷照片
V=6.3:
1
Causeofdefect缺陷成因
Causedbynon-metallicinclusionsduringproductionofhotsteelstriporcausedbysmallsurfacedefectsoriginatedinproductionofhotrolledsteelstrip.
该缺陷是由于热轧带中的非金属夹杂或热轧钢带表面的缺陷造成的。
Acceptance检验
Defectisacceptedwithinspecifiedroughnessifoccurringsporadically(analogfinegrooves).
如果缺陷是零星出现并满足粗糙度要求则可以判定为合格(类似于小的刻痕)。
Sorbitex75-Rtmax.3µmforthickness<0.15mmresp.5µmforthickness>0.15mm
厚度0.15mm以下的材料粗糙度可接受范围Rtmax.3µm,厚度大于0.15mm以上材料,粗糙度可接受范围Rtmax.5µm
Sorbitex80/90-Rtmax.3µmforthickness<0.60mmresp.5µmforthickness>0.60mm
厚度0.60mm以下的材料粗糙度可接受范围Rtmax.3µm,厚度大于0.60mm以上材料,粗糙度可接受范围Rtmax.5µm
Typeofdefect(缺陷类型)
Shell剥落
Definition说明
Irregular,flakyoverlappingmaterialwithnonmetallicinclusions.
不规则的薄片状非金属夹杂
Appearance缺陷形貌
Overlappinginvariousformswhichvaryinsize.Theyoccurirregularandisolated.
Shellsaresignalizede.g.duetospreadofuppersurfacelayers.
各种重叠形状。
缺陷的发生是无规则的孤立出现的。
剥落是非常明显的缺陷比如上层表面的分离。
Picture缺陷照片
V=6.3:
1
Causeofdefect缺陷成因
Duetoformationofrelativelylargeclustersofnonmetallicinclusionsduringthecontinuouscastingprocessorareattributabletomouldandflamescarfingdefects.
该缺陷的主要成因是铸造过程中产生的非金属夹杂造成的
Acceptance检验
Defectisnotaccepted.
出现该缺陷则产品判为不合格
Typeofdefect(缺陷类型)
Holes孔洞
Definition说明
Discontinuitiesinmaterialwhichpassrightthroughfromtoptobottomsurface.
贯穿于钢带上下表面,非连续出现
Appearance缺陷形貌
Discontinuitiesofdifferentkindandsize.Occurrenceisirregularandisolated.
非连续的不同种类和形状。
单独不连续出现。
Picture缺陷照片
V=6.3:
1
Causeofdefect缺陷成因
Holesoccurasaresultofmaterialtearing,duetolocalweaknessinthestripcrosssection,e.g.becauseofprematerialdefectsorseveremechanicalinjuriesofthesurface.
孔洞的产生是由于金属撕裂造成的,由于钢带局部强度不足造成。
主要由于原料缺陷或钢带表面受到机械损伤造成。
Acceptance验收
Defectisnotaccepted.
出现该缺陷则产品判为不合格
Typeofdefect(缺陷类型)
Rolledinexternalparticles
杂质轧入
Definition说明
Externalparticlescancontaminatethesteelstripineveryproductionstep.
在冷轧的各个环节都可能由于钢带污染造成此类缺陷
Appearance缺陷形貌
Slipmarksimilarsurfacedefects.Inetchedcrosssectionnormallyaswhiteparticlesvisible.Crosscracksanddeformationfiguresasresultofcoldrolling.Punctualonsurface.
与滑痕缺陷类似。
一般在缺陷区域可见白色杂质。
缺陷表现出来的横裂纹和变形是由于轧制造成的。
在钢带表面清晰可见。
Picture缺陷照片
V=6.3:
1
Causeofdefect缺陷成因
Externalparticlespressedinstripsurface
外部杂质颗粒压入钢带表面
Acceptance检验
Acceptableonlyaf
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 轧钢 表面 检查 缺陷 综述