汽轮机基础作业指导书.docx
- 文档编号:9919498
- 上传时间:2023-02-07
- 格式:DOCX
- 页数:22
- 大小:58.52KB
汽轮机基础作业指导书.docx
《汽轮机基础作业指导书.docx》由会员分享,可在线阅读,更多相关《汽轮机基础作业指导书.docx(22页珍藏版)》请在冰豆网上搜索。
汽轮机基础作业指导书
目录
CONTENTS
1.目的purposes
2.范围Scope
3.职责Responsibilities
4.参考文件References
5.计量器具、工具、机械Measuringinstruments,tools,machinery
6.劳动力组织Laborforce
7.施工工序和施工方法Constructionprocedureandplans
8.附件Attachments
1.范围Scope
本作业指导书适用于CSPC南海石化项目Steam&Power生产区汽轮机基础承台的施工。
ThisworkinstructionappliedtotheconstructionofsteamturbinefoundationcapinS&PproductionareaforCSPCNANHAIpetrochemicalsproject.
2.目的Purposes
规定中建三局二公司在CSPC南海石化项目汽轮机基础施工中的施工工艺及标准,以有效的控制施工质量及施工进度。
ItstipulatesthattheconstructionprocedureandstandardofChinesebuildingNO.3bureauforSEPCC2forCSPCNANHAIPETROCHEMICALSPROJECT,toeffectivelycontroltheconstructionqualityandtheschedule.
3.职责Responsibilities
技术负责人Techniqueleader陈群ChenQun
施工负责人Constructionlesders李晓东、方瑞青LiXiaodong,FangRuiqing
技术员Technician石青松ShiQingsong
施工员Constructors胡燕青、杨志猛、张立平HuYanqing,YangZhimeng,ZhangLiping
质检员Inspector王福全WangFuquan
测量员Surveyors郑小峰、潘江涛ZhengXiaofeng,PanJiangtao
安全员Safetyman李新军LiXinjun
4.参考文件References
4.1相关设计图纸;Relativedesigndrawing
4.1.1桩承台布置图(43-8320-8130-0101,REV.01)
Pilecapcollocationdrawing(43-8320-8130-0101,REV.01)
4.1.2桩承台1-1剖面图(43-8320-8130-0102,REV.01)
1-1sectiondrawingforpiledrawing(43-8320-8130-0102,REV.01)
4.1.3桩承台2-2、3-3、4-4、5-5剖面图(43-8320-8130-0103,REV.01)
2-2、3-3、4-4、5-5sectiondrawingforpilecap(43-8320-8130-0103,REV.01)
4.1.4桩承台配筋图(43-8320-8130-0104,REV.01)
Blendingrebardrawingforpilecap(43-8320-8130-0104,REV.01)
4.1.5桩承台1-1配筋剖面图(43-8320-8130-0105,REV.01)
Blendingrebarsectiondrawingforpilecap(43-8320-8130-0105,REV.01)
4.1.6桩承台2-2、3-3配筋剖面图(43-8320-8130-0106,REV.01)
2-2、3-3Blendingrebarsectiondrawingforpilecap(43-8320-8130-0106,REV.01)
4.1.7桩承台布置图(43-8320-8130-0108,REV.01)
Collocationdrawingforpilecap(43-8320-8130-0108,REV.01)
4.1.8桩承台配筋图(43-8320-8130-0109,REV.01)
Blendingrebardrawingforpilecap(43-8320-8130-0109,REV.01)
4.2与施工图纸相关的设计变更文件;
Thedesignchangedocumentiscorrelativetotheconstructiondrawing
4.3混凝土结构规范(SP-8320-8100-0002)Specificationofconcretestructure
4.4GB50202-2002
4.5GB50204-2002
5.计量器具、工具及机械Measuringinstrument,toolsandmachinery
计量器具:
全站仪、水准仪、钢卷尺
Measuringinstrument:
wholestation,waterlevel,steeltape
工具:
铁锹、镐、锤头
Tools:
shovel,pickax,hammerhead
机械:
混凝土泵车两台、搅拌车三台、砼振动器4台、4∽6米振动棒6个、钢筋切断机2台、弯钢机3台、辊丝机一台(所有机械进厂前应进行认真检查,并报有关部门审查通过后方能进入现场施工)。
Machinery:
2concretepumptrucks,3mixingtrucks,4concretevibrators,6vibratedsticksfor4∽6m,2rebarcutters,3benders,1threadroller(Allmachinemustbecarefullyinspectedandreportedbytherelateddepartmentbeforemobilizingintothesite).
6.劳动力组织Laborforce
技术员1人,施工员3人,测量员2名、质检员1名,安全员1名,壮工20名,熟练操作工3名,驾驶员3人,电工2人,焊工4人,木工50人,钢筋工25人,瓦工(砼工)25人,壮工10人
1technician,3constructors,2surveyors,1inspector,1safetyman,20laborworkers,3skillfulworkers,3drivers,2electricians,4welders,50woodworkers,25rebarworkers,25concreteworkers,10labors
7.施工工序和施工方法Constructionprocedureandplans
7.1施工工序constructionprocedure
施工工序为:
测量放线(土方开挖边线)→土方开挖→桩头处理→垫层施工→测量放线(轴线定位,模板边线)→底层砖胎模施工→钢筋绑扎→上层木模板支设、加固→质量验收→承台砼浇灌、养护→柱头钢筋模板施工→柱头钢筋模板验收→柱头砼浇注、养护→拆模清理
Measuringline(excavationsideline)→earthworkexcavation→disposalforpiletip→baseconstruction→Measuringline(axesorientation,formworksideline)→constructionoflowerbrickformwork→reinforcementplacement→upperformworkplacement→qualityinspectionandacceptance→foundationconcretepouringandcuring→columnreinforcementandformworkplacement→columnreinforcementandformworkinspectionandacceptance→columnconcreteplacementandcuring→formworkremovalandcleanup
7.2施工方法constructionmethod
7.2.1土方开挖excavation
7.2.2垫层施工baseconstruction
基础素土夯实完成经验收合格后,进行垫层施工。
按要求做好砖胎模。
用水准仪打上标高线,垫层浇砼时必须压实、压平。
Tocarryoutplainconcreteplacementaftersoilbaseacceptance.Thebrickformisapplicableandtheelevationshallbemarked.
7.2.3测量放线surveyingandmarking
施工前将垫层顶部清理干净,由测量人员组织木工在垫层上放出各中轴线及基础各中心线,红油漆涂三角符号标志,经复核无误后交验收。
中轴线及基础中心线经复核验收后,木工人员根据各基础中心线分别将基础模板边线(模板内边线)、基础收阶模板边线及上部柱段模板边线用墨线弹出,必要时四角用红油漆三角符号标志,经复核无误后方可进行模板施工。
Tocleanthesurfaceofbaseandtheaxislinesandfoundationcenterlinesonthebaseshallbemarkedandinspected.Theformworksidelineshallbealsomarkedaccordingtothefoundationcenterline.
7.2.4模板工程formwork
因汽轮机基础承台截面高度较大,且一部分标高较低,故承台下层模板采用砖胎模,高度为1.5m,宽度为240mm。
上层模板仍采用1220×2440标准镜光面胶合板。
砖胎模上表面与木模交接处应用水泥砂浆抹平,木模安装完以后再用水泥砂浆将接缝嵌填密实,以保证接缝严密,防止漏浆。
木模板表面应干净,无污渍及缺棱掉角现象。
模板相互拼装时在拼缝内填海绵条予以封堵,防止拼缝处漏浆,影响砼质量。
模板(包括支撑)应根据具体要求画出几何图形以便支模时能保证他们正确的位置、形状及横断面,从而使得最终的砼构件能够在允许的尺寸偏差之内。
施工时在地面预先按设计尺寸进行组合,与设计尺寸不符时按设计尺寸进行切割,要求断面整齐,校核无误后再进行组合安装。
重复使用的模板要求进行编号。
模板缝采用海绵条封堵。
模板安装前应涂刷隔离剂,应涂刷均匀。
涂刷后应由专人检查,避免局部漏刷,影响砼表面观感。
Thebrickformisappliedforthelowerformworkoffoundation,whichis1.5mhighand240mmwide.Theupperformworkadopts1220X2440typicalplywoodwithsmoothsurface.Thejointsofthemshallbefilledwithmortarfortightness.Inordertoensurethedimensionoffoundationwithintheallowabledeviation,theformworksketchshallbepreparedforconstructiontoshowthecorrectlocation,profileandsection.Therecycledformworkshallbenumberedandthejointofformworkbefilledwithspongestrips.
支撑系统用直径48mm长3.5m钢管搭设脚手架。
模板支撑要求具有足够的强度、刚度和稳定性。
考虑汽轮机基础承台尺寸较大,对拉螺杆施工不方便,拟采用背钢筋再拉螺杆的方法。
具体施工方法为:
在基础承台主筋内侧加一根直径22的钢筋,横向放置并与承台竖向主筋绑扎固定,将螺杆一端弯折,挂在此横向钢筋上并绑扎固定,然后再穿出与模板木枋固定。
螺杆横向间隔300距离设置,竖向第一道距离地面300,以上间隔500设置一道。
Thesupportsystemadoptspipes48mmdiameterand3.5mlong,whichshallbestrongandstableenough.Forpullingboltsfortie,firsttoplacearebar22diametertransverselyintheinsideofmajorrebar,thenhookoneendoftheboltandfixtothetransverserebar,andgothroughtheformworkandfixed.Thepullingboltsshallbearrangedat300transverselyand300abovegroundand500uppervertically.
固定模板用背枋净空尺寸为150mm。
然后为横向钢管,从砖胎模上100mm布置第一道横钢管,然后间距500mm一道,最后一道离上口不得超过100mm。
同时外侧用钢管支撑在四周承台上用以加固。
支模后,模板几何尺寸减少5mm,以减少混凝土胀模对混凝土尺寸的影响。
Theformworkisfixedbythetimber150mmandsupportedbytransversepipes.Thedimensionshallbe5mmlesstoreducetheaffectofconcreteexpansion.
模板垂直偏差不大于5mm,平直度不大于10mm,中心线位置偏差不大于5mm。
Theverticaldeviationshallnotmorethan5mm,thestraightnessbenotmorethan10mmandcenterlinedeviationbenotmorethan5mm.
7.2.5钢筋施工reinforcement
进厂钢筋经检测中心取样合格后,方可使用。
Allrebarsshallbetestedandacceptablebeforeuse.
首先根据图纸要求做出钢筋翻样单,经施工负责人、钢筋分队审批合格后方可进行钢筋配料,钢筋配料统一在钢筋场制作。
钢筋应被捆扎放置并且保证离地面至少300mm。
Therebarshallbecutaspertheapprovedrebarcutsheetatthefabricationarea.
现场钢筋必须按规格挂好标志牌,注明钢筋规格、型号、使用部位及试验结果、状态、情况。
放置时可以不用覆盖,但是有凹痕的地方不能生锈,且关键部位的应力不能降低。
钢筋应根据国标GB50204或BS8110或CEB-FIP规范进行切割、弯曲。
所有的钢筋都应避免被铁锈、氧化皮、油等物质污染,因为一旦被污染可能会减少钢筋强度并且降低与混凝土的粘结力。
Therebarshallbetaggedwithtype,locationandtestresults.ThecuttingandbendingshallbecarriedoutaccordingtoGB50204orBS8110orCEB-FIP.Allrebarsshallbefreefromrust,oxidationscaleandoiletc.likelytoreducethestrengthordurabilityofbondbetweensteelandconcrete.
钢筋成品、半成品运至现场后,分别按规格、型号堆放整齐,底部用方木等垫高防止泥水污染。
因汽轮机基础承台高度较高,先绑扎底层钢筋,然后搭设内侧辅助脚手架,用于承台顶层钢筋的绑扎,再绑扎顶层钢筋及中间竖向架立筋。
顶层钢筋绑扎时留部分缺口,将中层水平钢筋放入,然后逐层绑扎。
待钢筋绑扎完形成稳固钢筋笼以后再将内侧脚手架拆除。
为保证钢筋竖向的稳定性,可在承台钢筋外侧用钢筋绑扎剪刀撑,待模板支设加固后再拆除。
钢筋绑扎严格按图纸设计规格、间距施工。
钢筋绑扎点要求:
基础底板钢筋间隔绑扎,柱头箍筋接头处全部绑扎,其余间隔绑扎。
固定钢筋应用20号铁丝绑扎,铁丝的末端应嵌入混凝土中以防腐蚀。
上层钢筋安装时采用钢筋马凳予以支撑固定,为保证马凳的稳定性,马凳形式采用一根立杆上下设两根水平钢筋的形式。
马凳钢筋直径与主筋相同。
垫块采用混凝土垫块,混凝土标号与基础承台混凝土标号相等,间距1米布置,底板及侧墙布置成梅花形,在阳角处绑扎两块混凝土垫块,以保证钢筋笼不偏移。
Rebarproductsandsemi-productsshallbestoredproperlyafterdeliveredatsite.Firsttoplacethelowerreinforcement,thentosetupinnerscaffoldingforsupportofthetopreinforcement,andplacethetopandintermediatesupportrebars.Theplacementofreinforcementshallstrictlybedoneinaccordancewithdrawings.Afterplacement,thescaffoldingshallberemoved.Therequirementofbindingpoint:
thebaserebarsshallbeboundalternately,alljointsofstirrupofcolumnbeboundwhileothersbeboundalternately.Steelreinforcementshallbeerectedsuchastoformarigidcagewithintheformwork,witheveryintersectionbeingboundtogetherwithbindingwirewhichshallbetiedinsuchamannerthattheendsofthewirepointinwardtomaintainthefullspecifiedcover.Steelstoolsofanapproveddiameterandspacingshallbeprovidedbetweenlayersofreinforcementwherenecessarytomaintaintherequiredpositions.Thespacerwithsameconcreteclasswiththefoundationisarrangedat1m.Theplumblossomspacersshallbeplacedintheslabandwall,andtwospacersbesetinthecolumncorner.
竖向钢筋接头连接方式采用绑扎形式连接。
钢筋绑扎后严禁踩踏,确因施工中造成的情况,在砼浇注前必须派钢筋工进行专门修复。
Thebindingisappliedtotheconnectionofverticalrebarjoint,andnotrampleisallowedafterreinforcementerection.
柱筋采用绑扎方式与承台主筋固定,防止承台混凝土浇注时柱筋偏移。
Thecolumnreinforcementistobeboundandfixedtothemainbarsoffoundationtoavoiditsmovementduringconcreteplacementoffoundation.
7.2.6混凝土施工concreteplacement
基础模板、钢筋施工完毕,经验收合格签证完毕后方可进行浇筑砼。
砼由搅拌站集中送料,两台汽车泵浇筑。
Theconcreteplacementshallbedoneonlyafterinspectionandacceptanceofformworkandreinforcement.Theconcreteistobesuppliedfromthebatchingplantandpouredbytwopumptrucks.
(1)、砼浇筑前准备工作
Preparationpriortoplacement
A、重新对钢筋、模板等仔细复核检查。
Torecheckthereinforcementandformwork.
B、充分清除模板中的垃圾和钢筋上的油污。
Tocleanuptheformworkandreinforcement.
C、自模板外侧将模板和垫层之间用1:
2水泥砂浆嵌填密实,防漏浆烂根。
Tofillthejointofformworkandbaseby1:
2mortartoavoidanyleakage.
D、充分检查水、电源是否到位,电源箱、振动棒、振动器、夜间照明灯具等是否良好、正常。
Tocheckforwaterandpoweravailable,andtoolsandlightingingoodconditions.
E、对所有施工人员进行详细的施工技术交底。
Togiveallinvolvedpersonsdetailedinstruction.
F、现场应进行清理,为砼泵车出入提供方便。
Toclearupthefieldfortheentranceofconcretepumptrucks.
G、联系气象台,获知最近的天气状况,做好预防措施。
Togetweatherinformationtopre
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 汽轮机 基础 作业 指导书